Water Regulations Approval Scheme Ltd

Directory Search Results

WRAS Approval Number: #2207350

Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.

Section:: 1465 Heaters
Section Subtitle:: Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:: 2207350
Size:: Secondary: 15mm compression. Primary: 22mm compression.
Marking:: Ideal heating printed on front casing. Model and size printed on drop down door.
Installation Requirements:: R001 R140 R360
Expiry date:: 31/07/2027
Proviso:: Supplied with a temporary filling loop. The filling loop must be installed with the appropriate backflow prevention device in accordance with clause G24.2, Guidance to the Water Supply (Water Fittings) Regulations 1999.
Model:: Logic Max Combi² C24 – UIN 228334, Logic Max Combi² C30 – UIN 228335, Logic Max Combi² C35 – UIN 228336, Logic + Combi² C24 – UIN 228329, Logic + Combi² C30 – UIN 228330, Logic + Combi² C35 – UIN 228331, Logic Combi² C24 – UIN 228307, Logic Combi² C30 – UIN 228308, Logic Combi² C35 – UIN 228309.

Approval Holder:: Ideal Boilers Ltd

Company Name
Ideal Boilers Ltd
Address
PO Box 103 National Avenue Hull East Yorkshire
Postcode
HU5 4JN
Country
United Kingdom
Phone
07775659359
General Email
ben.higinbotham@groupe-atlantic.co.uk

View All Listings by this Company
Manufacturer:: Ideal Boilers Ltd

Company Name
Ideal Boilers Ltd
Address
PO Box 103 National Avenue Hull East Yorkshire
Postcode
HU5 4JN
Country
United Kingdom
Phone
07775659359
General Email
ben.higinbotham@groupe-atlantic.co.uk

View All Listings by this Company

WRAS Approval Number: #2207042

Water control valve with a DZR brass body and EPDM ‘O’-rings. The product incorporates a pressure sensor, ultrasonic sensor, temperature sensor and a motorised spherical valve with a DZR brass ball (chrome plated) and PTFE seats. Maximum working pressure 16.0 bar. Cold water use only.

Section:: 1530 Miscellaneous Fittings
WRAS Approval Number:: 2207042
Note:: This product has not been tested or approved for leak detection and automatic shut-off claims made by the approval holder.
Size:: ¾” BSP (F) inlet and outlet.
Marking:: TOLLCO on adhesive label on body. CR, Size, flow arrow and HELA on body.
Installation Requirements:: R001
Expiry date:: 31/07/2027
Model:: 2120013 Waterunit - Control (DN20).

Product Images

Approval Holder:: Tollco AB

Company Name
Tollco AB
Address

View All Listings by this Company

WRAS Approval Number: #2207328

Range of pressure limiter with stainless steel spring, plastic or chrome plated brass bodies. A5.0022.0 and A5.0027.0 incorporate with a stainless-steel mesh filter. Maximum working pressure 10.0 Bar. Maximum operating temperature 65˚C.

Section:: 1530 Miscellaneous Fittings
WRAS Approval Number:: 2207328
Note:: Pressure limiting claims made by the manufacturer have not been verified by test.
Size:: see model
Marking:: A5.0006.0, A5.0014.0, A5.0022.0, A5.00229.0, A5.0027.0: Neoperl moulded on body of insert, Neoperl & direction flow arrow etched on body A5.0004.0, A5.0010.0, A5.0020.0, A5.0025.0: Neoperl moulded on body of insert
Installation Requirements:: R001
Expiry date:: 31/07/2027
Model:: A5.0004.0 Pressure Limiter D 1bar insert - 18.57mm OD A5.0006.0 Pressure Limiter G1/2 1 bar - ½”BSP(F) x ½”BSP(M) A5.0010.0 Pressure Limiter 2 bar insert - 18.57mm OD A5.0014.0 Pressure Limiter D G1/2 2 bar - ½”BSP(F) x ½”BSP(M) A5.0020.0 Pressure Limiter DS 1 bar insert - 18.57mm OD A5.0022.0 Pressure Limiter DS G1/2 1 bar - ½”BSP(F) x ½”BSP(M) A5.0025.0 Pressure Limiter DS 2 bar insert - 18.57mm OD A5.0027.0 Pressure Limiter DS G1/2 2 bar - ½”BSP(F) x ½”BSP(M) A5.0029.0 Pressure Limiter DS G1/2 2 bar - OF - ½”BSP(F) x ½”BSP(M)

Product Images

Approval Holder:: Neoperl GmbH

Company Name
Neoperl GmbH
Address
Klosterrunstrasse 9-11, Müllheim
Postcode
D-79379
Country
Germany
Phone
+49 7631 188 374
General Email
DE.Approvals@neoperl.com

View All Listings by this Company
Manufacturer:: Neoperl GmbH

Company Name
Neoperl GmbH
Address
Klosterrunstrasse 9-11, Müllheim
Postcode
D-79379
Country
Germany
Phone
+49 7631 188 374
General Email
DE.Approvals@neoperl.com

View All Listings by this Company

WRAS Approval Number: #2203372

Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.

Section:: 1530 Miscellaneous Fittings
WRAS Approval Number:: 2203372
Note:: Suitable for backflow protection up to fluid category 3. Consult your water supplier prior to installation
Size:: ½” BSP (M)
Marking:: BOSS on front case.
Installation Requirements:: R001
Expiry date:: 31/03/2027
Model:: BOSS Direct G4 PERMANENT FILLING/PRESSURISATION DEVICE

Approval Holder:: BSS Industrial

Company Name
BSS Industrial
Address
Travis Perkins PLC Ryehill House Rye Hill Cose Lodge Farm Industrial Estate Northampton
Postcode
NN5 7UA
Country
United Kingdom
Phone
07392109053
General Email
benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

WRAS Approval Number: #2205095

Range of vertical multistage booster pumps, with stainless steel bodies and impellors. Maximum working pressure: See models Maximum working temperature 85°C.

Section:: 1610 Pumps
Section Subtitle:: Wholesome water use.
WRAS Approval Number:: 2205095
Size:: See Models
Marking:: Stuart Turner, CE, Max Temperature and other Technical info on Data Plates
Installation Requirements:: R001 R415
Expiry date:: 31/05/2027
Model:: VM(.) 1 >> Size from 2 to 39 stages VM(.) 3 >> Size from 2 to 33 stages VM(.) 5 >> Size from 2 to 27 stages VM(.) 10 >> Size from 2 to 23 stages VM(.) 15 >> Size from 1 to 17 stages VM(.) 20 >> Size from 1 to 16 stages VM(.) 32 >> Size from 1 to 14 stages VM(.) 45 >> Size from 1 to 13 stages VM(.) 64 >> Size from 1 to 8 stages VM(.) 90 >> Size from 1 to 6 stages ( ) = VM >> AISI304 Components (L) = VM >> AISI316L Components (K*) = VM>> AISI304 + PRESSURE SENSOR (LK*) = VM >> AISI316L + PRESSURE SENSOR *K1 = DANFOSS MBS1900 *K2 = DANFOSS DST P 140 *K3 =SCHNEIDER XMLP0xxBD21F VM(.) 1-3 >> Available with Oval flange G1, Round Flange DN25, Loose round flange DN25, Victaulic DN32 and Clamp Ø59 VM(.) 5 >> Available with Oval flange G1¼, Round Flange DN32, Loose round flange DN32, Victaulic DN32 and Clamp Ø59. VM(.) 10 >> Available with Oval flange G1½, Round Flange DN40, Loose round flange DN40, Victaulic DN50 and Clamp Ø87. VM(.) 15-20 >> Available with Oval flange G2, Round Flange DN50, Loose round flange DN50, Victaulic DN50 and Clamp Ø87. VM(.) 32 >> Available with Loose round flange DN65. VM(.) 45 >> Available with Loose round flange DN80. VM(.) 64-90 >> Available with Loose round flange DN100. Model Bar VM( )1 2 16 VM( )1 3 16 VM( )1 4 16 VM( )1 5 16 VM( )1 6 16 VM( )1 7 16 VM( )1 8 16 VM( )1 9 16 VM( )1 10 16 VM( )1 11 16 VM( )1 12 16 VM()1 13 16 VM(L)1 14 16 VM( )1 16 16 VM( )1 18 16 VM( )1 20 16 VM( )1 22 16 VM( )1 24 16 VM( )1 26 16 VM( )1 27 25 VM( )1 29 25 VM( )1 32 25 VM( )1 34 25 VM( )1( 37 25 VM( )1 39 25 VM( )3 2 16 VM( )3 3 16 VM( )3 4 16 VM( )3 5 16 VM( )3 6 16 VM( )3 7 16 VM( )3 8 16 VM( )3 9 16 VM( )3 10 16 VM( )3 11 16 VM( )3 12 16 VM( )3 13 16 VM( )3 14 16 VM( )3 15 16 VM( )3 16 16 VM( )3 17 16 VM( )3 19 16 VM( )3 21 16 VM( )3 23 25 VM( )3 25 25 VM( )3 27 25 VM( )3 29 25 VM( )3 31 25 VM( )3 33 25 VM( )5 2 16 VM( )5 3 16 VM( )5 4 16 VM( )5 5 16 VM( )5 6 16 VM( )5 7 16 VM( )5 8 16 VM( )5 9 16 VM( )5 10 16 VM( )5 11 16 VM( )5 12 16 VM( )5 13 16 VM( )5 14 16 VM( )5 15 16 VM( )5 17 16 VM( )5 19 25 VM( )5 20 25 VM( )5 23 25 VM( )5 25 25 VM( )5 27 25 VM( )10 2 16 VM( )10 3 16 VM( )10 4 16 VM( )10 5 16 VM( )10 6 16 VM( )10 7 16 VM( )10 8 16 VM( )10 9 16 VM( )10 10 16 VM( )10 11 16 VM( )10 12 16 VM( )10 14 16 VM( )10 15 16 VM( )10 16 25 VM( )10 18 25 VM( )10 19 25 VM( )10 21 25 VM(L)10 22 25 VM( )10 23 25 VM( )15 1 16 VM( )15 2 16 VM( )15 3 16 VM( )15 4 16 VM( )15 5 16 VM( )15 6 16 VM( )15 7 16 VM( )15 8 16 VM( )15 9 16 VM( )15 10 16 VM( )15 11 16 VM( )15 12 25 VM( )15 13 25 VM( )15 15 25 VM( )15 17 25 VM()20 1 16 VM( L)20 2 16 VM( )20 3 16 VM( )20 4 16 VM( )20 5 16 VM( )20 6 16 VM( )20 7 16 VM( )20 8 16 VM( )20 9 16 VM( )20 10 25 VM( )20 11 25 VM( )20 12 25 VM( )20 13 25 VM( )20 14 25 VM( )20 15 25 VM( )20 16 25 VM( )32 1-1 16EVMS( )32 1-0 16 VM( )32 2-2 16 VM( )32 2-0 16 VM( )32 3-2 16 VM( )32 3-0 16 VM( )32 4-2 16 VM( )32 4-0 16 VM( )32 5-2 16 VM( )32 5-0 16 VM( )32 6-2 16 VM( )32 6-0 16 VM( )32 7-2 16 VM( )32 7-0 16 VM( )32 8-2 25 VM( )32 8-0 25 VM( )32 9-2 25 VM( )32 9-1 25 VM( )32 10-2 25 VM( )32 10-0 25 VM( )32 11-2 25 VM( )32 11-1 25 VM(L)32 12-2 30 VM(L)32 12-0 30 VM( )32 13-2 30 VM( )32 13-0 30 VM( )32 14-2 30 VM( )32 14-0 30 VM( )45 1-1 16 VM( )45 1-0 16 VM( )45 2-2 16 VM( )45 2-0 16 VM( )45 3-2 16 VM( )45 3-0 16 VM( )45 4-2 16 VM( )45 4-0 16 VM( )45 5-2 16 VM( )45 5-0 16 VM( )45 6-2 25 VM( )45 6-0 25 VM( )45 7-2 25 VM( )45 7-0 25 VM( )45 8-2 25 VM( )45 8-0 25 VM( )45 9-2 25 VM( )45 9-0 25 VM( )45 10-2 35 VM( )45 10-0 35 VM( )45 11-2 35 VM( )45 11-0 35 VM( )45 12-2 35 VM( )45 12-0 35 VM( )45 13-2 35 VM( )64 1-1 16 VM( )64 1-0 16 VM( )64 2-2 16 VM( )64 2-1 16 VM( )64 2-0 16 VM( )64 3-2 16 VM( )64 3-1 16 VM( )64 3-0 16 VM( )64 4-2 16 VM( )64 4-1 16 VM( )64 4-0 16 VM( )64 5-2 16 VM( )64 5-1 16 VM( )64 5-0 16 VM( )64 6-2 25 VM( )64 6-1 25 VM( )64 6-0 25 VM( )64 7-2 25 VM( )64 7-1 25 VM( )64 7-0 25 VM( )64 8-2 25 VM( )64 8-1 25 VM( )90 1-1 16 VM( )90 1-0 16 VM( )90 2-2 16 VM(L)90 2-0 16 VM(L)90 3-2 16 VM(L)90 3-0 16 VM(L)90 4-2 16 VM( )90 4-0 16 VM( )90 5-2 25 VM( )90 5-0 25 VM( )90 6-2 25 VM( )90 6-0 25

Approval Holder:: Stuart Turner Ltd

Company Name
Stuart Turner Ltd
Address
47 Market Place Henley-on-Thames Oxfordshire
Postcode
RG9 2AD
Country
United Kingdom
Phone
01491 572655
General Email
stuart.savill@stuart-turner.co.uk

View All Listings by this Company