Gate valve with a blue epoxy coated ductile iron body and an EPDM lined disc, with a non-rising spindle operating mechanism. Maximum operating temperature: 80°C. Maximum working pressure: of 16.0bar.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models SCM020000535, SCM025000536, SCI100000533, SCM025002164 & SCM032002165 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models 41020, 41025, 41032, 31050 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Electrolytic inline limescale reducer with a zinc plated brass body and a copper coil. Maximum working pressure 10 bar. Maximum operating temperature 80°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Continuous soft water, ion exchange, hydraulically driven water softener (salt regenerated) for domestic use, incorporating LLDPE tubing. Operation is by an ion exchange resin filed plastic pressure vessel, with integral salt cabinet and timer/manual regeneration control. The appliance incorporates single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature Cold water only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'ULTRAFORM® N4320 003 AT UNCOLORED'. Natural (appears white), injection moulded POM material. For use with water up to 85°C.
'REVIMEN Bituminous Paint'. Factory applied, black coloured Bituminous paint. Apply as per manufacturer's TDS/Application Application Method 'AM25001', issued 'March 5, 2025'. Cure for 8 hours@25°C at a relative humidity of less than 85%. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'RAL 5005 Epoxy Coating'. Factory applied, blue coloured Epoxy Coating. Apply as per manufacturer's TDS '31.05.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 529 of 556
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
