Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves operate via a hand wheel. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves FIG. 100 and FIG. 100LK with bronze bodies and bronze wedges. The valves operate via non-rising spindle head work with hand wheel or lock shield operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C
Range of gate valves with bronze bodies with metal seats. The valves operate via a non-rising spindle headworks that incorporate a wheel type operating member or lock shield type (see models) Maximum working pressure 20.0 bar. Maximum operating temperature 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of 2, 3 or 4 way manifolds incorporating brass bodies (nickel plated), stop valves and EPDM seats. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies and PTFE seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 65ºC.
Screw down stop valve (chromium plated brass) incorporating a dome (triangular) type operating member with a NBR rubber washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85.0°C
Range of double regulating valves with bronze bodies, PTFE disc face and orifice plate, and EPDM rubber ‘O’-rings with thermostatic control elements and a manually adjustable flow control valve. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of ultraviolet disinfection units incorporating isolation valves and draw off tapes. Maximum working pressure 16.0 bar. Maximum operating temperature 50ºC.
Range of ultraviolet disinfection units with stainless steel bodies, quartz sleeves and silicone seals. Maximum working pressure 6.8 bar. Maximum operating temperature 40°C.
'Delrin® FG100 NC010'. White coloured (opaque), injection moulded acetal material. For use with water up to 85°C.
'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (white coloured). Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials, (manufactured in Bangkok, Thailand). For use with water up to 85°C.
'Delrin® FG100P NC010'. White coloured, injection moulded acetal material. For use with water up to 23°C.
'PUC-SC15'. Grey coloured silicon carbide seal ring manufactured by pressing and sintering. For use with water up to 85°C.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM1-SR3 - Dalmia SRPC'. Factory applied, grey coloured sulphate resisting Portland cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22. Cure for 4 days at 26°C, and then at 32°C for a further 24 days OR 24 hours@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubotaseal BM'. Factory applied, black coloured asphaltic bituminous coating. Apply as per manufacturer's PDS reference `11004T-1.4' dated Feb, 20, 2020. Cure 6 hours@20°C. For use with water up to 60°C. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'MORAPOX-WP'. Factory applied, two-part, red coloured epoxy coating comprising of a paint and hardener. Mix paint and hardener in a 2:1 volume ratio. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Conpipe Portland Cement Mortar NEN-EN 197-1 CEM II / A-LL 32,5 R'. Factory applied, grey coloured cementitious mortar lining. Mix cement and sand in a 1:1.1 mass ratio. Add water to cement in a mass ratio of 0.3-0.4. Cure for 28 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 6 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
