'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'C100E' & 'C100ELT'. Orange coloured ion exchange resins. For use with water up to 85°C.
'F15222 CB Silicone Lubricant' & 'PHCB042 – F15222 Centerbrand Silicone Grease'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'HEP PB Pipe'. Off-white coloured, extruded Polybutylene-1 pipe. For use with water up to 85°C.
'HEP PB Fittings'. Off-white coloured, injection moulded Polybutylene-1 fittings. For use with water up to 85°C.
'Radius Systems Puriton Dark Blue Barrier Pipe [Type A, BS8588]'. Extruded, multi-layered pipe comprising of a black coloured PE100 inner layer, aluminium middle later and dark blue coloured PE100 outer layer. For use with water up to 23°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'BLAZE PPR01'. Green coloured (with red external stripe), extruded polypropylene pipe. For use with water up to 85°C.
'3P764921 Pipe Spacer'. White coloured (opaque), injection moulded PP Pipe Spacer. For use with water up to 85°C.
'SABIC® PP 48M10'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'SABIC® PP 56M10'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'Tecoflex TU40 GR30 GR128 HS D6 QF'. Light grey coloured, injection moulded TPU material. For use with water up to 23°C.
'DS MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 28', dated 03.04.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NS’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 23.04.2025'. Cure for 4 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'10 EPR 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'15 EPR, 22 EPR & 28 EPR 'O' rings'. Black coloured, injection moulded 'O' rings. Shore hardness 60. Tested in-radius size 1.8mm. For use with water up to 85°C.
'51M5536'. Black coloured, injection moulded EPDM material. Shore hardness 55 ShA. Tested in-radius size 0.5mm. For use with water up to 23°C.
'EXJ2024'. Black coloured, compression moulded EPDM material. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'VL1001P279'. Blue coloured, compression moulded silicone rubber. Shore hardness 60. Tested in-radius size 0.99mm. For use with water up to 65°C.
'CarboStop 102/CarboStop 102 ACC'. Site applied, cream coloured (once applied) waterstop. Mix CarboStop 102 resin and CarboStop 102 ACC accelerator in a weight ratio of 20:0.4. Apply and cure as per manufacturer's Application Guide, revision date '19/09/25'. For use with water up to 23°C. This material is for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 492 of 506
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
