Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of stop valves with brass bodies and T-type operating members. Compression connecitons are for use with copper pipes (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'L-01 GP Blue-grey Enamel'. Factory applied, blue-grey coloured Enamel coating. Apply as per manufacturer's TDS 'Version: 01', dated '2025-01-02'. Cure for 15 minutes@200°C and then fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing/firing conditions that appear on the approval. If the cure/fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSP/SF-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Genesis FBE 5010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS issued 'August 2025'. Cure for 10 minutes@200°C. For use with water up to 23°C.
'VPC5022 Signal Blue FBE'. Factory applied, blue coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per manufacturer's Product Data Sheet 'VPC5022', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC8001 Gloss Black FBE'. Factory applied, black coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per Product Data Sheet 'VPC8001', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusion Bonded Epoxy (IMP-FBE) Cobalt Blue RAL 5013'. Factory applied, dark blue coloured epoxy coating. Pre-heat the substrate to 200°C and spray apply one coat at 120°C as per manufacturer's TDS 'YHRFBE2504', version 'V0'. dated '2025/3/27'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MC-PROOF 4200 AE'. Site applied, cream coloured (once mixed), two-component urethane based coating. Mix Part A (amber liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS dated 07.10.2025. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Berusil SM 2000'. Clear, liquid lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Tritan™ TX2001'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 Version: 0, 19/11/2020’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Reno 100+'. Dual layered, extruded polyethylene pipe comprising of a black coloured inner and blue coloured outer layer. For use with water up to 23°C.
Page 46 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
