'JSGL-OPC (U)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BELPA CSA 50'. Light green coloured, NBR/fibre gasket material manufactured by calendaring. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'ADPF GRE Pipe'. Green coloured GRE pipe manufactured by filament winding. For use with water up to 70°C.
'Synolite 5410-P-4'. Pink/brown coloured polyester laminate/GRP material manufactured by hand-lay. For use with water up to 23°C.
'Grilon AG-50 FWA Black'. Black coloured, injection moulded PA66-GF50 material. For use with water up to 60°C.
'Grilon TSG-30/4 FA Black 9840'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'Genestar G1350A-M47WF Black'. Black coloured, polyamide 9T material for injection moulding and extrusion purposes. For use with water up to 85°C.
'Mapex® AN4720SN (+)'. Natural (appears beige coloured), injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
Grilamid LBV-30H FWA natural & black 9225. Grilamid LBV-50H FWA natural & black 9225. Grilamid LBV-65H FWA natural & black 9225. Glass filled (30%, 50% & 65%), injection moulded nylon material available in natural and black colours. For use with water up to 85°C.
'CCP Longlite® PBT 1100-600S'. Off-white coloured, injection moulded PBT material. For use with water up to 50°C.
'SAFE 10 (H10 + H09, H17 + H04 and N08 + N04)' pipes. Extruded, dual-layered PE pipes comprising of a black coloured inner layer and blue coloured outer layer. Please note that the codes in brackets denote the raw material combinations and only these combinations are approved. In April 2025 ‘H10, H17 & N08’, extruded, single-layered, black coloured PE pipes were added to the approval. Only pipes marked with ‘H10, H17 or N08’ are approved. For use with water up to 40°C.
'EP EGEPLAST PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'CIPHON HDPE PIPE PE100'. Black coloured (with blue stripe), extruded PE100 pipe. For use with water up to 65°C.
'Diamant, Carat XL/XXL, Platin, Platin XL/XXL, Spring Water Shaft & Space-Saving Tank’ panels. White coloured (opaque), roto-moulded PE panels The approval includes panels manufactured in Germany (from September 2024 onwards) and France (from December 2024 onwards). For use with water up to 23°C.
'Tatren HG 10 07'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'BA160E-8229-01'. Black coloured, injection moulded polypropylene material. For use with water up to 85°C.
'17520'. Black coloured, calendared, Chlorobutyl material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 65°C.
'EP701443C 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.75mm. For use with water up to 85°C.
‘E27 EPDM moulded parts'. Black coloured, injection moulded EPDM seals. Shore hardness 75. Tested in-radius size between 0.8mm & 4.0mm. For use with water up to 85°C.
Page 382 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
