'18521 Kanepox Lining Free Cream or Red for use with Kanepox Hardener 0362'. Factory applied, two-part, cream or red coloured epoxy coatings consisting of component A (18521) and component B (0362). Mix and apply as per date sheet ‘Rev. No. 11’ dated February 2018. Cure for 7 days@23°C. The cream coating is for use with water up to 50°C. Between February 2024 and August 2024, the red coating is for use with water up to 23°C. From September 2024 the red coating is for use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Hempadur 3556K’. Factory applied, cream coloured epoxy coating consisting of a two-part primer and two-part top coat. The two-part primer is Hempadur 15590 red (56880) and this is mixed in a volume ratio of 7.93:2.14 and applied as per manufacturer's Product Data Sheet dated February 2024. Cure for 24 hours@20°C. The two-part top coat is Hempadur 3556K cream (20320) and this is mixed in a volume ratio of 6.8:2 and applied as per manufacturer's Product Data Sheet dated March 2024. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Hempadur 3556K’. Factory applied, cream coloured epoxy coating consisting of a two-part first coat and two-part second coat. The two-part first coat is Hempadur 3556K light red (50900) and this is mixed in a volume ratio of 6.8:2 and then cured for 24 hours@20°C. The two-part second coat is Hempadur 3556K cream (20320) and this is mixed in a volume ratio of 6.8:2 and then cured for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempaline® Defend 630 Cure 72', blue coloured coating. Between February 2024 and April 2025, the blue coloured coating was for use with water up to 50°C. Between May 2025 and February 2029, the blue coloured coating is for use with water up to 80°C. In May 2025, 'Hempaline® Defend 630 Cure 72', white coloured coating was added to the approval. For use with water up to 80°C. Factory applied, two-part epoxy phenolic coatings consisting of a base and curing agent. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's Product Data Sheet dated May 2025. Cure for 6 days@20°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Raymond Microsilica Modified Cement Mortar Standard A'. Site applied, grey coloured cement mortar. Mix cement/sand in a 1:1.1 mass ratio. To this add micro silica at 7%, achieved by mixing cement mix/micro silica in a mass ratio of 1:0.07 and water at 1:0.32 (cement mix/water). Add the MasterPozzolith 55R at a ratio of 2.2ml per kilo of cement. Apply as per manufacturer’s TDS ‘TDS/RI/2024/MMCM “Standard A’, dated ‘ 21 Feb 2024’. Cure for 28 days at a temperature of between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ES 988 DWPU'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv2.17102018'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flomasta Silicone Grease (Product Number 684RM)'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'LEXAN EXL1494T-NA8A005T'. Colourless, injection moulded Polycarbonate material. For use with water up to 85°C.
'T-NO.100S'. White coloured (translucent) PET mesh manufactured by weaving. For use with water up to 45°C.
Page 379 of 625
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
