'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VALVFIT 001 (blue) & VALVHIT 002 (red) Epoxy Powder Coatings'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'VALVFIT-2412001' dated '12.17.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP015-UTB'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions reference 'PR-CA-00-024' dated 15-02-19. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SikaTop® 550 Seal’. Site applied, white coloured, two component Acrylic, Cementitious waterproofing coating. Mix 1kg of part A (powder) with 333g of part B (liquid) and apply as per manufacturer’s method statement ‘10/2024’. Cure for 28 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM 35'. Site applied, grey coloured natural cement mortar. Mix cement mortar with water in the ratio of 25kg:3.6 litres and apply as per manufacturer's IFU 'issue 4', dated '21 February 2023'. Cure/set for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'Tufcot T100'. Off-white coloured, polyester composite material manufactured by hand lay-up. For use with water up to 23°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
‘Georg Fischer (+GF+) HDPE PE100 Pipes and ‘Hepworth MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'Polyfab PE100 Pipe' (manufactured by Polyfab Plastic Industry LLC in Ajman & Kizad). Black coloured (with blue external stripes), extruded PE100 pipe. For use with water up to 85°C.
'Polyfab PE100 Fittings' (manufactured by Polyfab Plastic Industry LLC in Ajman & Kizad). Black coloured, injection moulded PE100 fittings. For use with water up to 85°C.
‘+GF+ HDPE PE100 Pipes' and '+GF+ MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'CR-01 PE Pipe'. Blue coloured, extruded PE pipe. For use with water up to 23°C.
'Kasta® HDPE PE 100 Pipe (Black)'. Black coloured (with blue external stripes), extruded HDPE pipe. For use with water up to 65°C.
'Egelen PE100 & Egeplast 9010 pipes'. Egelen PE100 is a single layered, black coloured, extruded PE100 pipe. Egeplast 9010 is a dual layered, extruded PE100 pipe consisting of a black coloured inner layer and a blue coloured outer layer. For use with water up to 23°C.
'Revolve N-250 Light Grey M2-5321'. Grey coloured PE material manufactured by rotomoulding. For use with water up to 85°C.
'Borealis HE125MO & Bn HE125MO-100'. White coloured (semi-opaque), injection moulded PP-H materials. For use with water up to 85°C.
'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 363 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
