Range of near boiling hot water dispensers with stainless steel tanks and flow is controlled via float switch. Maximum working pressure 3 Bar. Maximum operating temperature 98°C.

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241202718

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/8” BSP M inlet/outlet

Marking:

KoGE by Scudo on body

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

KoGE WATER DISPENSERS

Approval Holder:

Harrison Bathrooms Incorporating Scudo

Company Name

Harrison Bathrooms Incorporating Scudo

Address

Prospect Works Keighley West Yorkshire

Postcode

BD21 4LA

Country

United Kingdom

Phone

01535 663024

General Email

adam.barnsley@harrisonbathrooms.com

View All Listings by this Company

Range of water meters with blue epoxy power coated cast iron bodies, incorporating plastic turbines, NBR ‘O’-rings and gaskets. Maximum working pressure 16.0 bar. BS6920 50°C.

Section:

1505 Water Meters

Size:

DN50 - DN200 flanged

Marking:

ARAD, address, model number and other technical info printed on dial face. Size and flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/10/2028

Model:

WSThp

Approval Holder:

Arad GROUP Ltd.

Company Name

Arad GROUP Ltd.

Address

Kibbutz Dalia 1923900 Kibutzz Dalia

Country

Israel

Phone

+972-4-9897906

General Email

Dars@arad.co.il

View All Listings by this Company

Range of in-line single jet water meters with brass bodies. Products incorporate plastic strainers. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 85.0°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN15 Models: 1/2” BSP (M) DN20 Model: 3/4” BSP (M).

Marking:

Flow arrow on body. BMETERS, serial number and other technical info on meter face.

Installation Requirements:

R001

Expiry date:

31/01/2030

Model:

HYDRODIGIT-S1 DN15 Length: 80mm, 110mm, 145mm, 165mm. DN20 Length: 130mm, 190mm.

Product Images

Manufacturer:

B Meters S.r.l

Company Name

B Meters S.r.l

Address

Via Friuli 3 33050 Gonars (UD) Italy

View All Listings by this Company

Mixing valve incorporating a brass body and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure10.0 bar. Maximum operating temperature 65°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F) captive nut

Marking:

Presto on body

Installation Requirements:

R001 R008 R010

Expiry date:

31/01/2030

Model:

29424 MIXER G1/2

Product Images

Manufacturer:

Les Robinets Presto S.A

Company Name

Les Robinets Presto S.A

Address

4 Rue Lavoiser St. Georges De Didonne

Postcode

17110

Country

France

Phone

+33 546 053 452

View All Listings by this Company

Range of click type, pop-up wastes with metal bodies. Maximum operating temperature 60.0°C

Section:

1535 Miscellaneous

Section Subtitle:

Tap accessories.

WRAS Approval Number:

241002704

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1 ¼” BSP (M)

Marking:

Vinzia Fratelli logo, EN274, NF logo and date of manufacturer (DDD/YY)

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

04, 05, 06 family types. Code example: 00 AA 00 00 00 00 AA(A). Made up of the below. TYPE OF WASTE (2 numbers) 04 - Waste Simple-Rapid with waste drains H60 – 75 – 100 05 - Waste Simple-Rapid with waste drains 06 - Waste free flow with all waste drains CAP (2 letters) AA - TA209 AB - TA204 AC - CO032 + TA406 (in this case the first two numbers are”04 or 05”) or TA200 + TA413 in this case the first two numbers are”06”) BA – TA191 BC – TA193 (in this case the first two number as “05”) or TA198 (in this case the first two number are”06”) BD – TA197 BE – TA195 BH – TA201 CA - TA6 + TA217 / TA229 (in this case the first two numbers are”04 or 05”) or TA6 + PA001 in this case the first two numbers are”06”) WASTE DRAIN (2 numbers) 01 - PI096 02 - PI087 03 - PI088 07 - PI096/STP 08 - PI110/STP 09 - PI088/STP 11 - PI082 19 - PI084/1STP 20 - PI084/1 21 - PI082/STP 24 - PI083 25 - PI083/STP 50 - PI099 51 – PI209 52 – PI210 62 – PI207 85 – PI010 BASE (2 numbers) 01 - RA095 02 - RA096 07 - CO110 16 - RA014 17 - RA009 50 - RA094 51 - RA100 54 - RA002 VARIANTS (2 numbers) 00 - STANDARD COMPONENTS PACKAGING (2 numbers) 00 - STANDARD PACKAGING FINISH (2 or 3 letters) CR - CHROME PLATED (these two letters are always compiled) + None - ME235-AB or no mechanism (for free flow ones) CRG - ME238

Product Images

Approval Holder:

VINZIA Fratelli S.p.A.

Company Name

VINZIA Fratelli S.p.A.

Address

Via Borgomanero, 121 Briga Novarese (NO)

Postcode

28010

Country

Italy

Phone

+39 0322 94847

General Email

gianfranco.calzoni@vinzia.com

View All Listings by this Company

‘UPM10’ and ‘UPM20’ range of circulator pumps with a stainless-steel body, plastic impellor and EPDM ‘O’-rings. The product is supplied with EPDM gaskets for the inlet and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241207701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1½” BSP (M) inlet/outlet.

Marking:

Grundfos and Grundfos logo, type and model on nameplate on motor housing. P/N no., P/C no., Serial (S/N) no., technical info, manufacturing country and data matrix on end of motor housing. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

UPM 10M 25-95 N 180, UPM 10L 25-105 N 180, UPM 10XL 25-125 N 180, UPM 20S 25-145 N 180. Where: Pump type: UPM 10M, UPM 10L, UPM 10XL, UPM 20S. Control variant: []: PWM, LIN: LIN bus input signal, 0-10V, AUTO, HYBRID, SOLAR, DHW. Nominal diameter: 25: G 1½”. Max. Head: 95: 9.5m, 105: 10.5m, 125: 12.5m, 145: 14.5m. Designation/Pump housing: N 180: Stainless steel body, 180mm port to port length. Control box orientation: 3: 3 o’clock (right), 6: 6 o’clock (below), 9: 9 o’clock (left). Customer code: XXX (no impact on water contact parts).

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Self-priming single stage pump, with stainless steel body, plastic impellers, stainless steel shaft, NBR 'O'-rings and seals. Maximum working pressure 6.0 bar. Maximum operating temperature 45°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241107701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” BSP (F).

Marking:

Grundfos and Grundfos logo on body. Grundfos and Grundfos logo, type, model number, product/version number, technical information, serial number and manufacturing location on adhesive label on motor housing.

Installation Requirements:

R001 R008 R415

Expiry date:

30/11/2029

Model:

99458789: JP 4-54 1X230V 50Hz 1,5M UK HU IE2.

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241002722

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Size:

P 3S & U 5S models: 1” BSP (F) inlet x 1” BSP (F) outlet. P 7S models: 1¼” BSP (F) inlet x 1” BSP (F) outlet. P 9S models: 1½” BSP (F) inlet x 1¼” BSP (F) outlet. P 18S models: 2” BSP (F) inlet x 1½” BSP (F) outlet.

Marking:

Foras (Brand of Pentax), model code and other technical information on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/10/2029

Model:

P range: P X(S) - XX/Y (T) Where: P = pump model X = Nominal flow-rate m³/h (3, 5, 7, 9, 18 see model list), S = ULTRA S range - stainless steel hydraulic part, XX = nominal power HPx100 (50 - 400 see model list), Y = Number of impellers (2 - 7 see model list), T = 3 phase, [blank] = single phase. P 3S models: P 3S-50/2; P 3S-70/3; P 3S-90/4; P 3S-100/5; P 3S-120/6; P 3S-150/7. P 5S models: P 5S-70/2; P 5S-80/3; P 5S-120/4; P 5S-150/5; P 5S-180/6; P 5S-200/7. P 7S models: P 7S-100/2; P 7S-120/3; P 7S-180/4; P 7S-250/5; P 7S-300/6. P 9S models: P 9S-100/2; P 9S-150/3; P 9S-200/4; P 9S-250/5. P 3S models: P 3S-50/2 T; P 3S-70/3 T; P 3S-90/4 T; P 3S-100/5 T; P 3S-120/6 T; P 3S-150/7 T. P 5S models: P 5S-70/2 T; P 5S-80/3 T; P 5S-120/4 T; P 5S-150/5 T; P 5S-180/6 T; P 5S-200/7 T. P 7S models: P 7S-100/2 T; P 7S-120/3 T; P 7S-180/4 T; P 7S-250/5 T; P 7S-300/6 T; P 7S-350/7 T. P 9S models: P 9S-100/2 T; P 9S-150/3 T; P 9S-200/4 T; P 9S-250/5 T. P 18S models: P 18S-180/2 T; P 18S-250/3 T; P 18S-400/4 T.

Approval Holder:

PENTAX INDUSTRIES SpA

Company Name

PENTAX INDUSTRIES SpA

Address

Viale dell’Industria 1 Veronella

Postcode

37040

Country

Italy

Phone

+39 0442 489567

General Email

g.cengia@pentax-pumps.it

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102722

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

ESPA, model & technical information on adhesive label on body.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

MULTI VSXXX-XX-(1/2/C/D/2C/2D/C-D) -(F/N) -E 1. XXX: Rated flow（m³/h）, Range:1~200 m³/h. 2. XX: Impeller progession，progession range:1~36. 3. 1/2/C/D/2C/2D/C-D: Extra impeller: --1or2，On behalf of the product with 1 or 2 small size impeller. --C or D，On behalf of the product with a size C or size D impeller. --2C or 2D，On behalf of the product with two size C or size D impellers. --C-D, On behalf of the product with a size C and a size D impeller. 4. F/N: the materials of wetted parts --N，material is SUS 316. --F，material is SUS 304. 5. E：E type end connection mode and size -- Rated flow(1-3m³/h) : DIN Flange connection DN 25 -- Rated flow(4-5m³/h) : DIN Flange connection DN 32 -- Rated flow(10m³/h) : DIN Flange connection DN 40 -- Rated flow(15-20m³/h) : DIN Flange connection DN 50 -- Rated flow(32m³/h) : DIN Flange connection DN 65 -- Rated flow(45m³/h) : DIN Flange connection DN 80 -- Rated flow(64-90m³/h) : DIN Flange connection DN 100 -- Rated flow(120-150m³/h) : DIN Flange connection DN 125 -- Rated flow(200m³/h) : DIN Flange connection DN 150

Approval Holder:

ESPA

Company Name

ESPA

Address

PO Box 8156 Warehouse Q4 - 123 Sharjah Airport Free Zone, Sharjah

Country

United Arab Emirates

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102723

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

TPF on cover. TPF, model & technical information on data label on body.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

TPVSXXX-XX-(1/2/C/D/2C/2D/C-D) -(B) -E 1.XXX: Rated flow（m³/h）, Range:1~200 m³/h. 2.XX: Impeller progession，progession range:1~36. 3. 1/2/C/D/2C/2D/C-D: Extra impeller: --1or2 ， On behalf of the product with 1 or 2 small size impeller. --C or D，On behalf of the product with a size C or size D impeller. --2C or 2D，On behalf of the product with two size C or size D impellers. --C-D, On behalf of the product with a size C and a size D impeller. 4.B: the materials of wetted parts --B，material is SUS 316. --None，material is SUS 304. 5.E：E type end connection mode and size -- Rated flow(1-3m³/h) : DIN Flange connection DN 25 -- Rated flow(4-5m³/h) : DIN Flange connection DN 32 -- Rated flow(10m³/h) : DIN Flange connection DN 40 -- Rated flow(15-20m³/h) : DIN Flange connection DN 50 -- Rated flow(32m³/h) : DIN Flange connection DN 65 -- Rated flow(45m³/h) : DIN Flange connection DN 80 -- Rated flow(64-90m³/h) : DIN Flange connection DN 100 -- Rated flow(120-150m³/h) : DIN Flange connection DN 125 -- Rated flow(200m³/h) : DIN Flange connection DN 150 THM(-3)XX-XX\XX-SE 1. -3: different phase. -- -3: three phase，none: single phase. 2.XX: Rated flow（m³/h），range: 2、3、4、8、10、12、 16、20m³/h. 3.XX: impeller progession (1,2,3,4,5,6,7) 4.XX: Small Impeller（1,2,3,4,5, ） 5.SE: SE Intelligent Type End connection mode and size Rated flow (2、3m³ /h) :G1"XG1" Rated flow (4m³ /h) :G1¼"XG1" Rated flow (8、10、12m³ /h) :G1½"XG1½" Rated flow (16、20m³ /h) :G2"XG2"

Approval Holder:

TADMUR PUMP FACTORY WLL

Company Name

TADMUR PUMP FACTORY WLL

Address

P.O. BOX 212023 DOHA

Country

Qatar

View All Listings by this Company