Range of normally closed solenoid valves with black or grey plastic bodfies, EPDM diaphragm and EPDM ‘O’-rings. The inlet incorporates a removable plastic strainer with a stainless steel mesh. The outlet incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of normally closed solenoid valves with plastic bodies and silicone diaphragms. Model DSVP12N-12LSX-240M has two inlets. Maximum working pressure 0.060 bar. Cold water use only.
Range of brass bodied (nickel plated) spherical valves incorporating PTFE seats & chrome plated ball. Maximum working pressure 40.0 bar.
Range of brass or DZR brass spherical valves incorporating single lever operating members and a chrome plated brass ball. Model 0312A030307DC is an angled 90-degree valve which incorporates single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 or 3). For use with EN1057 copper pipe. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising resilient stem seated gate valves with epoxy coated bodies and EPDM wedge. Maximum working pressure 16 bar. Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron bodies ,EPDM gasket, EPDM wedge and a handwheel operating member. Maximum working pressure 25 bar. Maximum operating temperature 80°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE washers. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising spindle gate valves, brass bodies, incorporating PTFE stem packing and gaskets with handwheel operating members. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with bronze bodies and bronze wedges. The valves operate via non-rising spindle head work with hand wheel or lock shield operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C
Range of thermal balancing valves with brass bodies and EPDM O-rings. The products also incorporates an analogue temperature gauge. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 90°C
Range of manually operated balancing valves with either a DZR brass or bronze body incorporating a non-rising spindle balancing mechanism. Valves are adjusted using a handwheel. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Pentens SPU-1000 Pure Polyurea Waterproofing Spray Coating (with Pentens E-500SE Primer and Pentens E- 501S Sealer)’. Factory applied, dark yellow coloured (once applied) polyurea primer, sealer & top coat. Mix primer in a 1:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix sealer in a 2:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix topcoat in a 1.125:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 72 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux Solvent Free DW Coating Grey and Red'. Factory applied, light grey or red coloured epoxy coatings. Apply as per manufacturer's data sheet number '558', revision '04', dated October 2022. Cure for 7 days@30°C. For use with water up to 30°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.
'TPU 2053, TPU 2054, TPU 2055, TPU 2056, TPU 2057 & TPU 2058'. Five layered, membrane systems manufactured by calendaring. The membranes consist of: 1.) a transparent polyurethane inner layer (in contact with the water), 2.) a tie layer, 3.) a reinforcing layer (PES or PA), 4.) a tie layer & 5.) a blue or beige coloured polyurethane outer layer (not in contact with the water). For use with water up to 23°C.
'P0667 Lid Support'. Light green coloured (opaque), GRP lid support component manufactured by pulltrusion. For use with water up to 23°C.
'DISTITRON® VE 100 ST'. Beige coloured, glass fibre reinforced Vinyl Ester Resin manufactured by hand lay-up. For use with water up to 23°C.
Page 338 of 555
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
