'Polywarm'. Factory applied, brown coloured enamel powder coating. Apply as per manufacturer's instructions '1024'. Cure for 20 minutes@240°C. For use with water up to 85°C.
'Interpon HYF PLUS HJ701I'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's product datasheet 'Ed.3 – October 2014' and stove/cure for 20 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Acothane DW Cream, Acothane DW Blue & Acothane DW Grey’ site applied, two-part polyurethane coatings to be used with or without ‘Acothane LV’ polyurethane sealer. ‘Acothane LV’ (base coat) and ‘Acothane DW Cream’ (base or middle coat) are approved for use as non-water contact coats. ‘Acothane DW Blue & Acothane DW Grey’ are approved as water-contact coats and may be used alone or as the water contact coat in any of the following combinations: Acothane DW LV Sealer/ Acothane DW Cream/ Acothane DW Blue. Acothane DW LV Sealer/ Acothane DW Cream/ Acothane DW Grey. Acothane DW Cream/ Acothane DW Blue. Acothane DW Cream/ Acothane DW Grey. Mix Part A & Part B of Acothane LV in a weight ratio of 100:48, apply as per TDS dated March 2022 and then cure for 4 hours@3°C before applying cream coating. Mix Part A & Part B of Acothane DW Cream in a weight ratio of 100:31, apply as per TDS ‘06ADW’, issue ‘2’, dated December 2022 and then cure for 4 hours@3°C before applying blue or grey water contact coat. Mix Part A & Part B of Acothane DW Blue/Grey in a weight ratio of 100:31, apply as per TDS ‘06ADW’, issue ‘2’, dated December 2022 and then cure for 7 days@3°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GRP-FPI-FIBERSTRONG'. Light green coloured, multi-layered GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'LZFRP-GP-01'. Green coloured GRP material manufactured by filament winding. For use with water up to 85°C.
'SIL70W01 hoses'. White coloured (translucent), extruded silicone hoses with a shore hardness of 70. Tested in-radius sizes between 0.25 and 2.0mm. For use with water up to 85°C.
'TapTec™ 350 UPS Na & TapTec™ 400 UPS Na'. Amber coloured ion exchange resins. For use with water up to 23°C. These materials incorporate synthetic cellulose. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'Vinoleo SO350'. White coloured (translucent), silicone oil lubricant. For use with water up to 85°C.
'Rotormagnet 12-0000294'. Dark grey coloured, injection moulded Polyamide + Strontium Ferrite magnet. For use with water up to 60°C.
'VYDYNE AG7K-BK1066'. Black coloured, (35% glass Fibre reinforced) polyamide 66 material. From 1st April 2023 until 29th May 2024, the material was for use with water up to 23°C. From 30th May 2024 until 30th April 2028, the material is for use with water up to 70°C.
'VYDYNE AG10K-BK1066'. Black coloured, (50% glass Fibre reinforced) polyamide 66 material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'A280G6 HF'. Off-white coloured, injection moulded PA66-GF30 material. For use with water up to 80°C.
'ForTii Ace WX51-FC BK00001, ForTii PA Xgea20 BK28049 & PA Xgea BK28049'. Black coloured, injection moulded PA 4T materials. For use with water up to 85°C.
'Aquaboost Impellor'. Off-white coloured, injection moulded PES impellor. For use with water up to 60°C.
'Aquaboost+ Impellor'. Light brown coloured, injection moulded glass filled PES impellor. For use with water up to 60°C.
'Hepworth HDPE PE 100 Pipe (black) & HDPE PE 100 Pipe (black with blue stripes)'. Extruded polyethylene pipes. For use with water up to 60°C.
'Almona PE100 Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 85°C.
'Fusamatic Electrofusion Fittings'. Black coloured, injection moulded, polyethylene Electrofusion Fittings (made in UK from Ineos Eltex TUB121 & Hostalen CRP 100 Resist CR Black). In December 2023, Electrofusion Fittings made in Anhui Province China from Borouge Borsafe HE3490-LS & Hostalen CRP 100 Resist CR black were added to the approval. For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
Page 321 of 555
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
