Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'HT204.V2'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'ZMF7405'. Factory applied, blue coloured Enamel coating. Apply as per manufacturer's TDS 'Version 01', issue date 'December 1, 2025'. Dry for 15 minutes@100°C and then furnace fire for 10 minutes@860°C. For use with water up to 85°C.
‘Nelfapox FW Inert Cream'. Factory applied, cream coloured, two-component epoxy coating. Mix base and curing agent in a 6.8:2 volume ratio. Apply one or two coats as per manufacturer's Technical Data Sheet '999', revision date '24-03-2026'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per National Paints technical data sheet 'FBE/ REV01 09-07-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ConProtect WP 1'. Liquid concrete admixture based on crystallization technology. To be added at a maximum of 2% of the cement weight as per manufacturer's TDS 'Version 3 - 2025'. Cure for 14 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Revolve M-638, M-694 & M-695'. Black coloured Polyethylene materials manufactured using rotational moulding. For use with water up to 85°C.
‘BOR Plus Faser Composite Stabil Pipe PP-R (SDR 6 & SDR 7.4)’. Extruded, multi-layered PP-R pipes comprising of a beige coloured inner layer, green coloured middle layer and beige coloured outer layer. ‘BOR Plus Monolayer PP-R Pipes (SDR 6 & SDR 7.4)’. Extruded, beige coloured PP-R pipes. For use with water up to 85°C.
'Smart S-IRV'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0141’, dated ‘29/11/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Smart S-IRE'. Site applied, light pink coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0187’, dated ‘29/11/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-3030'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 17/0694’, dated ‘09/09/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 17/0694’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-2+’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 14/0346’, dated ‘07/11/2025’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 14/0346’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'OLD B254 50N'. Black coloured, injection moulded IIR material. Shore hardness 50 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'Spira Power 4070 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'Jelt VA 15-77 (yellow coloured), Jelt VA 15-72 (white coloured) & Jelt VA 16-48 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SHAFPUR/CH | Chrome | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SHAFPUR/BN | Brushed Nickle | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SHAFPUR/AB | Antique brass | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SHAFPUR/GD | Gold | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| AVEPUR/CH | Chrome | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| AVEPUR/BN | Brushed Nickle | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| AVEPUR/AB | Antique brass | 1/2" BSP | 10bar bar | 60℃ °C | Caple logo | on body | No | 1/4 Turn ceramic disc | C-plate | Aerator |
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of WC flushing cisterns incorporating a side entry (delayed action) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The float operated valve incorporates a flow restrictor on the inlet. The cistern is operated by an optional manual dual push button and incorporates a servicing valve on the inlet supply. The waste elbow on model BDS-K210-A01-ESG6 is optional. Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 108-7010 | Chrome plated | 1/2" BSP (F) | 10 bar | 60 °C | CEILSA | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 310-7010 | Chrome plated | 1/2" BSP (F) | 10 bar | 60 °C | CEILSA | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
Page 320 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
