'Tesnit BA-U(G)'. Blue coloured fibre/NBR material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Sealtex ST-2052'. Green coloured NBR/fibre material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Himod Flat Seal 15'. Grey coloured, fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
`YT-001`. Single layer, extruded, white coloured PEX hose. For use with water up to 85°C.
'Lewatit S 8227 & S 8229. White coloured ion exchange resins. For use with water up to 23°C
'Aldex C800 Na (16-50 US mesh resin), Aldex C800x10 Na (16-50 US mesh resin), Aldex C800F (Na) (30-70 US mesh resin) & Aldex C800F (K) (30-70 US mesh resin)'. Ion exchange resins which are black coloured except C800F (Na) which is brown coloured. For use with water up to 23°C.
'TP1'. Factory applied, colourless solid lubricant. Apply as per manufacturer's instructions 'LDAP-005', issue 1, dated 11/11/2016. For use with water up to 85°C.
'Ultramid S3EG6 Balance Aqua Uncoloured'. Uncoloured (appears beige), injection moulded PA6/10 material. For use with water up to 85°C.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'Grilon BG-35/2 natural & Grilon BG-35/2 black 9697'. Natural (appears white coloured, opaque) and black coloured, injection moulded PA6-GF35 materials. For use with water up to 85°C.
'Ketaspire KT-820 NT & KT-820 NL PEEK'. Beige coloured, injection moulded PEEK materials. For use with water up to 85°C.
'PALCONN PEX-AL-PEX Pipe'. Multi-layered, extruded pipe comprising of a transparent PEX inner layer, aluminium middle layer and white coloured PEX outer layer. For use with water up to 85°C.
'Superpipe PE-RT Type 2 Pipe'. Multi-layered, extruded pipe consisting of a white coloured (translucent) PE-RT inner layer, aluminium middle layer and white coloured (opaque) PE-RT outer later. For use with water up to 85°C.
'Revolve M-2638 Black'. Black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Revolve 4068/N-250 (white coloured), M-586 (black coloured), M-638 (black coloured), M-694 (black coloured) & M-695 (black coloured)'. Polyethylene materials manufactured using rotational moulding. For use with water up to 85°C.
‘LONGLITE®PSRP1000 natural (appears yellow/brown coloured), black (black coloured) & white (appears off-white coloured)’. Injection moulded PPSU materials. For use with water up to 85°C.
'Akansu Boru Green Pipe'. Green coloured, extruded PP pipe. For use with water up to 85°C.
'Greentherm Pipe'. Green coloured, extruded polypropylene pipe. For use with water up to 85°C.
'Greentherm Fitting'. Green coloured, injection moulded polypropylene fitting. For use with water up to 85°C.
`Maxxam PP Flow Meter Insert`. Off-white coloured, injection moulded polypropylene flow meter insert. For use with water up to 23°C. From September 2023, the component is for use with water up to 85°C.
'Fusio-Technik faser Fiber-T'. Extruded, multi-layered pipe comprising of a white coloured PP-RCT inner layer, grey coloured PP-R+GF middle layer and green coloured PP-R outer layer. For use with water up to 85°C.
'ECONTEC'. Green coloured, extruded PP-RCT pipe. For use with water up to 85°C.
'Banninger PP-RCT Fittings'. Green coloured, injection moulded PP-RCT fittings. For use with water up to 85°C.
'Moplen EP 300 K PP Cover'. White coloured, translucent, injection moulded polypropylene cover. For use with water up to 85°C.
'DETAI'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'Evinox Ball Valve PTFE Sealing Ring'. White coloured (opaque), compression moulded PTFE sealing ring. For use with water up to 85°C.
‘Monomix’. Site applied, grey coloured waterproofing mortar. Mix 'Monomix' and water in a 7.58:1 mass ratio. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP1/1/5 BLK EPDM Diaphragm'. Black coloured, compression moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
'EP80/2 BLK 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Tested in-radius size 1.5mm. For use with water up to 85°C.
EP80/2 BLK 'O' rings & gaskets. Black coloured, injection moulded EPDM 'O' rings & gaskets. Shore hardness 80. Tested in-radius size 1.5mm. . For use with water up to 85°C.
'09-557'. Black coloured, compression moulded EPDM 'strip'. Shore hardness 80. Tested in-radius size 2.0mm. For use with water up to 85°C.
'EP5700'. Black coloured, compression moulded EPDM material. Shore hardness 57. Tested in-radius size 0.98mm. For use with water up to 23°C.
'EP70B002'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
`WN 22/1/9 BLK` 'O' rings. Black coloured, injection moulded, nitrile rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 65°C.
'SIL60 RED 'O' rings and seals'. Red coloured, injection moulded silicone rubber 'O' rings and seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.77mm. The seals have a tested in-radius size of 0.90mm. For use with water up to 85°C.
'Griffon WDF-05'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6311380 20200708'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Beaulon P5250N Grey & Beaulon P5250N White'. Compression moulded, thermoplastic Polybutene materials. For use with water up to 85°C.
'Ixef DW/FC 1032 BK001 (black coloured) & Ixef DW/FC 1032 NT000 (natural, appears off-white coloured)'. Injection moulded PARA (polyarylamide) materials. For use with water up to 85°C.
'Hytrel® 6359FG & 4068FG'. Cream coloured, injection moulded, thermoplastic polyester elastomeric materials. For use with water up to 85°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated, tap assemblies (chromium plated brass). Flow is controlled via solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator, supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of side entry BS1212-4 (2016) delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern is operated by a manual push button. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern is operated by manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded, resilient trim, in-line check valve cartridge with plastic guide, stem, body and EPDM O-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spring loaded resilient trim in-line check valve cartridge with plastic guide, stem and housing, stainless steel spring and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, resilient trim, in-line check valve cartridgse, with plastic guides & jumper and NBR or EPDM seals within a plastic housing. For insertion in pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Models NV20/DN20-EPDM 31.0004.0 & NV20/DN20-pr 31.0071.0 have a maximum operating temperature of 60°C. Models NV20/DN20 31.4221.0 & NV20/DN20-HT 31.0011.0 have a maximum operating temperature of 85°C.
Range of spring loaded, resilient trim, in-line check valve cartridge, with plastic guides & jumper and NBR or EPDM seals within a plastic housing. For insertion in pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Model 31.4220.0. has a maximum operating temperature of 85°C. Model 31.0003.0 has a maximum operating temperature of 60°C.
Page 4 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
