'662016 & 662014'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
'INST61427N & INST61425T Tapes'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
'STAR PIPE VULGARI.EPE PVC PRESSURE PIPE EN1452'. Black coloured, extruded PVC pipe. For use with water up to 23°C.
'Buffalo PUR500'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '14/08/2018'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'07148-70' components. Black coloured, compression moulded EPDM components with a shore hardness of 70. Sealing gaskets have an in-radius size of 1.0mm. Sealing membranes have an in-radius size of 0.92mm. Gasket membranes have an in-radius size of 0.85mm. Membrane seals have an in-radius size of 1.0mm. Sealing rings have an in-radius size of 1.0mm. For use with water up to 85°C.
‘07146-80’ components. Black coloured, compression moulded EPDM components with a shore hardness of 80. Sealing Gasket with an in-radius of 1.5mm. Membrane Seal with an in-radius of 1.0mm. Sealing Gasket with an in-radius of 1.0mm. Gasket Membrane with an in-radius of 1.0mm. Sealing Ring with an in-radius of 1.0mm. For use with water up to 85°C.
'ML 57314'. Black coloured, compression moulded EPDM material. Shore hardness 68A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 30114010102A Black'. Black coloured, compression moulded EPDM sheet material. Shore hardness 75. Tested in-radius size 3.0mm. For use with water up to 85°C.
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Floor mounted single hole, single outlet (fixed), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure - 10 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of AB air gap arrangements (verified by test - suitable for backflow protection against Fluid Category 5), supplied with or without softeners and/or flow meters (see models). Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of Type TK spring loaded, resilient trim, in-line check valve cartridges. For insertion into specifically dimensioned bores. Maximum working pressure 10.0bar. Maximum operating temperature 65ºC.
Thermostatic cartridges with plastic or brass bodies, and EPDM ‘O’ rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. BS6920 85°C.
‘VT30’ range of thermostatic cartridges with a plastic body and EPDM ‘O’-rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. BS6920 70°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Single-hole, single outlet, fixed, combination tap assembly with (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever type pop-up waste. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed combination tap assemblies, (chrome plated brass bodies), incorporating ceramic cartridge headworks. The spout outlets incorporate plastic aerators (TTR1086 & TR1088) or flow straightener (TR1084). Maximum working pressure 5 bar. Maximum operating temperature 85°C
Page 30 of 67
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
