'PPNBH 1002 nut, body and holder'. Black coloured, injection moulded, polypropylene nut, body and holder component. For use with water up to 23°C.
'Aquatherm Fitting'. Green coloured, injection moulded polypropylene fittings. For use with water up to 60°C.
'Innopol CS 4-8000 G'. Grey coloured, compression moulded polypropylene material. For use with water up to 60°C.
'TFM1700'. White coloured, injection moulded PTFE ring. For use with water up to 85°C.
'7EP2114 'O'-rings'. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'4255 Washers', with a tested in-radius size of 1.0mm. '4255 ‘O’ rings', with a tested in-radius size of 1.31mm were added to the approval in September 2023. Black coloured, injection moulded EPDM washers & ‘O’ rings. Shore hardness of 50. For use with water up to 85°C.
'ERIKS 55950 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 3.5mm. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'FKM 90 Black 6019020105-CMP00700'. Black coloured, compression moulded FKM material. Shore hardness 90. Tested in-radius size 1.1mm. For use with water up to 85°C.
'ROGM 2022 'O' ring'. Black coloured, injection moulded NBR 'O' ring. Shore hardness 70. Tested in-radius size 4.4mm. For use with water up to 23°C.
‘KSIL70’. Natural (off-white coloured), silicone rubber gaskets manufactured by pulltrusion. Shore hardness 70. Tested in-radii sizes between 0.55mm & 0.85mm. For use with water up to 85°C.
‘Loctite® 55’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Technical Data Sheet ‘reference 1.9’, dated August 2016 and this material is only approved for these conditions. For use with water up to 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated – brass bodies). Flow is controlled via a solenoid which is actuated via an infrared sensor and the temperature is controlled by a manual lever. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and a manual lever to control the outlet temperature. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Temperature:60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Range of ceramic cartridge headworks with plastic bodies, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Quarter turn ceramic disc headwork with brass body, NBR and silicone rubber ‘O’ rings, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Non-metallic materials and components comply with BS6920 at 90°C
Range of single hole or two-hole pre-rinse taps (chromium plated brass bodies) which have either a single outlet or two outlets. The flow is controlled by rising spindle headworks with single lever operating members and the spout outlet incorporates a plastic flow straightener. Model 89001MN-2 is a single hole tap with two outlets; a spout (swivel) outlet and pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98001-1, 98001-1-01, 98001MN-1, 98001MN-1-01 are two-hole taps with a single outlet; a pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98007MN-2, 98007MN-2-01, 98007-2 & 98007-2-01 are two-hole taps with two outlets; a spout (swivel) outlet and pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98007MN-1 & 98007MN-1-01 are two-hole taps with a single outlet; a pull-down pre-rinse assembly which incorporates a trigger mechanism. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Page 285 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
