'221K'. Beige coloured, compression moulded ceramic washer. For use with water up to 85°C.
‘Series 2000 – Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 29-0008: Description RAL9005 Black Deep FBE. Code 29-0008: Description RAL5015 Blue Sky. Code 29-0008: Description RAL5005 Blue Signal. Apply as per Powder-Lak (Pty) Ltd. technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BFSC RIZHAO S&M&B DN 22'. Factory applied, grey coloured Blast Furnace Slag Cement Mortar Lining. Mix cement and sand in a weight ratio of 1:2.2. Mix this with water in a 0.46:1 weight ratio. Apply as per manufacturer's TDS '1008', dated '20221008'. Cure for 9 hours at 60°C & 95% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VIMPOTABLE 34 EPOXY PAINT'. Factory applied, two-component, red coloured epoxy coating. Mix Parts A & B in a 3:1 volume ratio and apply as per manufacturer's Technical Bulletin 'VP/02', issue date '01.01.2021'. Cure for 7 days@50°C. For use with water up to 45°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TEPICOMPOWDER PC-200F U'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'A/W AQUA (A) Epoxy 100'. Site applied, pale straw coloured epoxy/linseed oil waterproof coating. Apply as per manufacturer's Technical Document 'FSQP-707-05' dated '2021.01.04'. Cure for 6 hours under UV light (wavelength 365μm) at a distance of 150mm. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lionpak 2100'. White coloured, braided, PTFE gland packing. For use with water up to 85°C. For use as a gland packing only having been tested at a reduced surface area to volume ratio.
Page 271 of 350
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
