Wall mounted spout outlet brass body (various finishes) incorporating plastic flow straightener. The inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0682 Combination Tap Assemblies

Section Subtitle:

Spout outlet(s).

WRAS Approval Number:

2303702

Size:

¾” BSP (M)

Marking:

Samuel Heath on Spout

Installation Requirements:

R001

Expiry date:

31/03/2028

Model:

V157-XX Where the product code suffix ‘XX’ denotes the surface finish. It will always be 2 or 3 digits, which can be any combination of numbers and/or letters. As examples: CP = chrome finish, URM = urban brass matt lacquered.

Approval Holder:

Samuel Heath & Sons Plc

Company Name

Samuel Heath & Sons Plc

Address

100 Leopold Street Birmingham

Postcode

B12 0UJ

Country

United Kingdom

Phone

+44 (0) 1217 662 200

General Email

kay.stead@samuel-heath.com

View All Listings by this Company

Manufacturer:

Samuel Heath & Sons Plc

Company Name

Samuel Heath & Sons Plc

Address

100 Leopold Street Birmingham

Postcode

B12 0UJ

Country

United Kingdom

Phone

+44 (0) 1217 662 200

General Email

kay.stead@samuel-heath.com

View All Listings by this Company

Electric, instantaneous, vented, mains water heaters with plastic housings and silicon gaskets. Incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 1.5 bar.

Non-metallic materials and components comply with BS6920 at 98°C

Section:

1365 Heaters

Section Subtitle:

Electric instantaneous, open outlet, mains fed.

WRAS Approval Number:

2210067

Size:

½” BSP male inlet x 3/8” BSP male outlet.

Marking:

PROBOIL.2X on body. Pressure and model on adhesive label on rear of body.

Installation Requirements:

R001

Expiry date:

31/10/2027

Model:

PROBOIL.2X

Approval Holder:

Norcros Group (Holdings) Limited T/A Abode

Company Name

Norcros Group (Holdings) Limited T/A Abode

Address

Unit L Zenith Park Whailey Road Barnsley

Postcode

S75 1HT

Country

United Kingdom

Phone

01226 283434

General Email

info@abode.eu

View All Listings by this Company

CR(I)(N)(E) ranges of multistage centrifugal pumps incorporating stainless steel impellers, intermediate chamber and outer sleeve. CR(E) versions have cast iron bases and pump heads coated with black cathodic paint. CRI(E) and CRN(E) versions have stainless steel bases and pumpheads. The pumps are available with the following shaft seals HQQ*, HUU*, HUB*, HQB*, where * can be E for EPDM and V for FKM. Maximum working pressures: CR1, 3 or 5 (2-36 stages) Oval flange: 16.0 bar. CR1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange: 25.0 bar CRI/N1, 3 or 5 (2-36 stages) Flexi clamp with oval flange connection: 16.0 bar CR/I/N1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange, PJE, Flexi clamp or Triclamp: 25.0 bar CR10 (1-16 stages) Oval flange or DIN/ANSI/JIS flange: 16.0 bar. CR10 (17-22 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI10 (1-16 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI10 (17-22 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar CRN10 (1-22 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR15 or 20 (1-7 stages) Oval flange: 10.0 bar. CR15 or 20 (1-10 stages) DIN/ANSI/JIS flange: 16.0 bar. CR15 or 20 (11-17 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI15 or 20 (1-7 stages) Flexi clamp with oval flange connection: 10.0 bar CRI15 or 20 (1-10 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI15 or 20 (11-17 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CRN15 or 20 (1-17 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR models: Cold water use only. CRI/CRN models: Cold water use only and from April 2023 99°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2210906

Size:

Oval flange: Rp 1” - 2”. Flexi Clamp Base: Small Base (CR/I/N1/1(s)/3/5) Ø32, Medium Base (CR/I/N15/20) Ø50. Triclamp Base Small Base (CR/I/N1/1(s)/3/5) DN32, Medium Base (CR/I/N15/20) DN50. Flange Base: Small Base (CR/I/N1/1(s)/3/5) DN25/32, Medium Base (CR/I/N15/20) DN40 and 50. PJE Base: Small Base (CR/I/N1/1(s)/3/5) DN32, Medium Base (CR/I/N15/20) DN50.

Marking:

Grundfos and Grundfos logo, type, Model, Product/Version no., technical info, temperature (WRAS 23C or WRAS 99C), manufacturing country on data plate on motor stool.

Installation Requirements:

R001 R415

Expiry date:

31/10/2027

Model:

CR(I)(N)(E) 1(s) range with 2-36 stages, CR(I)(N)(E) 3 range with 2-36 stages, CR(I)(N)(E) 5 range with 2-36 stages, CR(I)(N)(E) 10 range with 1-22 stages, CR(I)(N)(E) 15 range with 1-17 stages, CR(I)(N)(E) 20 range with 1-17 stages. Model keycode: CR(E)(C) 1/1(s)/3/5/10/15/20-A B-C-D-E-XXXE, CRI(E)(C) 1/1(s)/3/5/10/15/20-A B-C-D-E-XXXE, CRN(E)(C) 1/1(s)/3/5/10/15/20-A B-C-D-E-XXXE. Where: CR = Pump type and Cast Iron, I = EN 1.4301, N = EN 1.4401, E = Preminum Electronically Controlled Motor, C = Core (Basic) with Electronically Controlled Motor. 1/3/5/10/15/20 = Flow rate [m³/h], (s) = Reduced impeller version. A = No. of stages. B = Code for pump version: A = Basic version, B = Oversize motor, E = Pump with certificate, G = E-pump without operating panel, H = Horizontal version, I = Different pressure rating, J = E-pump with a different maximum speed, L = Pump including Grundfos CUE and certificate, N = With sensor, O = Clean and dryed, P = Undersize motor, R = Belt driven pump, V = Cascade function, X = Special version*, Z = Pump with bearing flange. C = Code for pipe connection: A = Oval flange, CA = Flexi clamp, CX = TriClamp, F = DIN flange, G = ANSI flange, J = JIS flange, N = Changed diameter of ports, P = PJE coupling (Victaulic). D = Code for materials: A = Basic version, C = Carbon-free pump, D = Carbon-graphite filled PTFE (bearings)/tungsten carbide, H = Flanges and base plate EN 1.4408, L = Motor stool, base plate and flanges EN 1.4408, N = Flanges EN 1.4408, R = Silicone carbide /silicone carbide bearing, S = PTFE neck rings, T = Baseplate EN 1.4408, X = Special*. E = Code for rubber parts: E = EPDM, V = Viton. XXX = Code for shaft seal: HQQ, HUU, HUB, HQB. [H = Balanced cartridge seal with O-ring, B = Carbon, synthetic resin-impregnated, U = Cemented tungsten carbide, Q = Silicon carbide]. *Special version ONLY covers the situation where more than 4 options are selected within the same position. This will automatically turn the 4 or more options into an X.

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

CR(N)(E) ranges of vertical multistage centrifugal pumps with stainless steel (CRN models) or black polymer coated cast iron bodies (CR models) and a stainless steel impeller. The products are available with or without a sensor. Maximum working pressure: 16.0 bar - CR(N)(E) 32 range with 1-7 stages, CR(N)(E) 45 range with 1-5 stages, CR(N)(E) 64 range with 1-5 stages. 30.0 bar - CR(N)(E) 32 range with 8-14 stages, CR(N)(E) 45 range with 6-11 stages, CR(N)(E) 64 range with 6-8 stages. 33.0 bar - CR(N)(E) 45 range with 12-13 stages. Maximum operating temperature - CR models are cold water use only. CRN models are cold water use only up to February 2nd 2023, and 99°C from February 3rd 2023.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2301900

Size:

CR/CRN 32: CR/CRN 32, 1-14 stages: DN65 and DN80 flange connection. CRN32, 1-14 stages: 3” PJE connection CR/CRN 45: CR/CRN 45, 1-13 stages: DN80 and DN100 flange connection. CRN45, 1-13 stages: 4” PJE connection. CR/CRN 64: CR/CRN 64, 1-8 stages: DN100 flange connection. CRN64, 1-8 stages: 4” PJE connection.

Marking:

Grundfos and Grundfos logo, model, type, prod/version no., technical information and manufacturing country on data plate on motor stool.

Installation Requirements:

R001 R415

Expiry date:

31/01/2028

Model:

CR/CRN(E) 32-A-B C-D-E-F-XXXX, CR/CRN(E) 45-A-B C-D-E-F-XXXX, CR/CRN(E) 64-A-B C-D-E-F-XXXX. Where: Type range: CR = Pump type and Cast Iron, N = EN 1.4401, E = Preminum Electronically Controlled Motor. 32, 45 or 64 = flow rate m³/h, A = number of impellers (CR/CRN 32 1-14, CR/CRN 45 1-13, CR/CRN 64 1-8). B = number of reduced impellers: 0, 1 or 2 on CR/CRN 32 1-7, CR/CRN 45 1-5, CR/CRN 64 1-8 models, 0 or 2 on all other models. C = Code for pump version: A = Basic version, B = Oversize motor, E = Pump with certificate, G = E-pump without operating panel, H = Horizontal version, I = Different pressure rating, J = E-pump with a different maximum speed, K = Pump with low NPSH, L = Pump including Grundfos CUE and certificate, N = With sensor, O = Clean and dryed, P = Undersize motor, R = Belt driven pump, V = Cascade function, X = Special version*, Z = Pump with bearing flange, D = Code for pipe connection: F = DIN flange, G = ANSI flange, J = JIS flange, N = Changed diameter of ports, P = PJE coupling (Victaulic). E = Code for materials: A = Basic version, C = Carbon-free pump, D = Carbon-graphite filled PTFE (bearings)/tungsten carbide, H = Flanges and base plate EN 1.4408, L = Motor stool, base plate and flanges EN 1.4408, N = Flanges EN 1.4408, R = Silicone carbide /silicone carbide bearing, S = PTFE neck rings, T = Baseplate EN 1.4408, X = Special*. F = Code for rubber parts: E = EPDM, V = Viton. XXXX = Code for shaft seal: HQQE or V / HUUE or V / HUBE or V /HQBE or V. H = Balanced cartridge seal with O-ring, B = Carbon, synthetic resin-impregnated, U = Cemented tungsten carbide, Q = Silicon carbide, E = EPDM, V = Viton. *Special version ONLY covers the situation where more than 4 options are selected within the same position. This will automatically turn the 4 or more options into an X.

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of booster pumps with plastic bodies and impellers, stainless steel shafts, brass manifolds, NBR ‘O’-rings and EPDM seals. The product incorporates a pressure vessel. The outlet(s) incorporate(s) an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The inlet hose(s) supplied with this product incorporate(s) an isolation valve. Maximum working pressure 4.0 bar. Maximum operating temperature 65°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2105325

Note:

IRN R150 applies to both inlets of the Twin models only.

Size:

Stainless-steel braided EPDM lined flexible hoses with 15mm pushfit (inlet and outlets) x ¾” BSP captive nut end connections (to pump).

Marking:

Bristan, model name & other technical information on adhesive label on pump body.

Installation Requirements:

R001 R150 R415

Expiry date:

31/05/2026

Model:

ST NHPUMP 20TN & 239574

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company