‘SABIC® Vestolen A 6060 R 10000 (black)’. Black coloured, extruded HDPE material. For use with water up to 23°C.
'Romaklima CT Pipe'. Green coloured (with white stripe), extruded, multi-layered pipe comprising of a a PP-RCT inner & outer layer and glass fibre middle layer. For use with water up to 70°C.
'Inoflon® GN7040 & Inoflon® MGN7045'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
'80EP251p 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 0.89mm. For use with water up to 85°C.
‘51M5577, 51M6077, 51M6577, 51M7077, 51M7577, 51M8077, 51M8577’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘TWK7534, TWK5810, TWK5811, TWK5812, TWK5813, TWK5814, TWK5815’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'4711'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'Spray SLC STD Inlay 24' & 'Spray SLC STD Inlay 16 Low'. Grey coloured, injection moulded, liquid silicone rubber components. Shore hardness 70. Tested in-radius size 0.44mm. For use with water up to 70°C.
'7751 'O' rings'. Blue coloured, compression moulded VMQ 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
'S70C'. Off-white coloured (translucent), compression moulded silicone 'O' rings. Shore hardness 70. Tested in-radius size between 0.89mm & 3.5mm. For use with water up to 85°C.
'Weld-On 725 Wet 'R' Dry Clear Solvent Cement'. Clear, colourless solvent cement. ‘Weld-On 725 Wet ‘R DRY Blue PVC Cement’ was added to the approval in September 2025. Blue coloured solvent cement. Cure for between 1 & 4 hours@5°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with chromium plated brass bodies. The flow is controlled by a solenoid valve activated via an infra-red sensor and a manually adjustable temperature lever. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled via a manual operating single lever on body. The inlets hose incorporates stainless steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection). The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
Range of spring loaded resilient trim check valve cartridges with acetal body and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Tundish incorporating a plastic body, nut and olives. The tundish complies with the requirements of air gap to drain. Maximum operating temperature 100°C
Page 231 of 583
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
