Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 10.0 bar and 16.0 bar (dependent on flange pressure rating). Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 16.0 bar and a maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass or DZR brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising shaft with a gear box operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with hand wheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of front loading commercial washing machines with flow controlled by solenoid valve and discharged via type AB air gap assembly. Maximum working pressure 6.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Electrolytic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitors with nickel plated copper bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Electrolytic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
McAlpine Scale Defender Limescale Inhibitor’. The product does not incorporate any backflow protection.. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
Electronically controlled, commercial ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only
'KEBAFORM C 90W natural' & 'KEBAFORM C 90W schwarz'. Natural (appears white) and black coloured, injection moulded POM materials. For use with water up to 65°C.
'EPW-6575S8T-20 Epoxy RAL 5005'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'Rev:00/December 2022'. Cure for 10 minutes at 200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied, black coloured PUR coating system comprising of a primer and topcoat. ‘Promag Primer’ is a two-part primer to be mixed in a 1:2 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 2 hours@23°C. ‘Promag Topcoat’ is a three-part topcoat to be mixed in a 92.59:5.19:2.22 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 20 seconds@20-26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purtop 1000 N'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS '7506-2-2023'. Cure for 48 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YT425'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'AYYT01' dated '2023.3.16'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Polywarm'. Factory applied, brown coloured enamel powder coating. Apply as per manufacturer's instructions '1024'. Cure for 20 minutes@240°C. For use with water up to 85°C.
Page 226 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
