Range of inline spherical valves, (nickel plated brass bodies), chrome plated brass balls, PTFE seats and washers with lock-shield, single lever or T-type operating members. Maximum working pressure: ¼” to 1” = 40.0 bar, 1¼” to 2” = 32.0 bar, 2½” to 3” = 25.0 bar, 4” = 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated, full bore spherical valves with brass bodies (brushed chrome) and chrome plated brass balls and a range of different operating members. Sizes ¼” to ½” have a maximum working pressure of 64.0 bar. Sizes ¾” to 2½” have a maximum working pressure of 40.0 bar. Cold water use only.
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA571ES Black 700 & PPA571 Black 700'. Factory applied Polyolefin PE Coatings. Apply 'PPA571 Black 700' by fluidised bed according to manufacturer's data sheet '08/2022' and dip in the bed for 5-8 seconds. Apply 'PPA571ES Black 700' by electrostatic spray according to manufacturer's data sheet '08/2022'. Cure for 190-200°C for 20 mins. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kinlin Epoxy Power Coating (Green colour, EPX‐111A)'. Factory applied, green coloured epoxy powder coating. Apply as per manufacturer's instructions 'XL-R-019-G1' dated '2018-9-21'. Cure for 10 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sunaflex T 8193'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Supercast PVC Waterstop Hydrofoil'. Blue coloured, extruded PVC waterstop. For use with water up to 23°C. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The materials have been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of single hole, single outlet, electronic touch free, deck mounted taps (chromium plated brass) for cold or premixed water. Flow is controlled via solenoid valves, actuated by infra-red sensors. Power is supplied by externally mounted 9V battery pack or 9V transformer. The inlet hoses have a stainless-steel strainer and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome/satin plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 22 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
