Range of spherical valves with brass bodies and chrome plated brass ball, PTFE washer and EPDM `O` ring and various operating methods. Maximum working pressure 10.0 or 40 bar (see model).
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies, chome plated brass balls and EPDM O-rings. Connection to be used with copper pipe EN1057. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Protecta-line range of screw down stopcocks with Gunmetal body’s incorporating NBR O-rings. The stopcocks are to be used with Protecta-line PE80 multi-layer pipe manufactured to BS 8558. Maximum working pressure 12.5bar. Cold water use only.
‘R-4401, E-44131, E-4413, E-4414, E-4420, E440001, E441001, E440002, E441002, E-5402, E-5403, E-5404, E540001. E541001, E540002, E540003, E541003 & E440007’. Factory applied, grey-blue coloured enamel coatings. Apply as per manufacturer’s instructions ‘issue 02/2016’ dated 05.10.2016. Cure for 6 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Borsafe ME3440 (black), Borsafe ME3444 (blue) & Borsafe ME3440-W (black)'. PE80 materials suitable for injection moulding and extrusion purposes. For use with water up to 60°C.
'Dowlex 2344'. Natural (appears white), compression moulded LLDPE material. From May 2025, the material may also be used for extrusion purposes. For use with water up to 85°C.
'Spray SLC STD Inlay 24' & 'Spray SLC STD Inlay 16 Low'. Grey coloured, injection moulded, liquid silicone rubber components. Shore hardness 70. Tested in-radius size 0.44mm. For use with water up to 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer and check valve cartridge(s), verified by test (suitable for backflow protection against Fluid Category 2). The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the spout to the solenoid. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar Maximum operating temperature - 60 °C
Page 22 of 73
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
