'Truform Cement OPC 43 Grade'. Factory applied, grey coloured cement. Mix cement:sand in a weight ratio of 2:1 and add 0.5 litres of water. Apply as per manufacturer's instructions 'TTPL/SOP/MCD/03', revision '00', dated 01.04.2018. Cure for 24 hours@27°C followed by 7 days@85°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purolite C104EPLUS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'Ultradur® B4520 FC Aqua uncolored'. Uncoloured (appears white), injection moulded PBT materials. For use with water up to 23°C.
'VIALLI-De SDR 6 & SDR 7.4 PPR pipes'. Green coloured, extruded PPR pipes. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 & SDR 7.4 Pipes with Glass Fibre Middle Layer'. Extruded PPR pipes with a green coloured inner and outer layer and a red coloured, glass fibre middle layer. For use with water up to 23°C.
'Ultrason® S 2010 G4'. Light beige coloured, injection moulded polysulphone material. For use with water up to 85°C
'662016, 662014, 662062 & 662061'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'IROGRAN® A 85 P 4441 FCM'. White coloured, injection moulded polyurethane material. For use with water up to 60°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
'EPDM4570‐70'. Black coloured, compression moulded gaskets. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
'AEC 2/EPDM-50, AEC 3/EPDM-60, AEC 4/EPDM-70 & AEC.A5/EPDM-80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
Page 210 of 310
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
