‘DURACON® M90-57 WK2001 & DURACON® M270-57 WK2001’. Grades 'M90-57 WK2001BG' & 'M270-57 WK2001BG' were added to the approval during September 2022. White coloured, injection moulded POM materials. For use with water up to 85°C.
‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply as per manufacturer’s technical data sheet 'no. 786.3' dated 2013-V2'. Cure for 5 hours@23°C or 30 minutes@50°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
`CY9198`. Grey coloured, pressed and kilned carbon/graphite thrust ring. For use with water up to 85°C.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 6070'. Factory applied, black coloured, electrodeposition coating. Apply and cure as per technical data sheet ‘LT/F-16-128’ dated October 20th 2016. For use with water up to 23°C.
'Flogul® 645 Vert 6013'. Factory applied, green coloured paint. Apply as per manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 195 of 1016
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
