'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2012-8-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
‘Pentens SPU-1000 Pure Polyurea Waterproofing Spray Coating (with Pentens E-500SE Primer and Pentens E- 501S Sealer)’. Factory applied, dark yellow coloured (once applied) polyurea primer, sealer & top coat. Mix primer in a 1:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix sealer in a 2:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix topcoat in a 1.125:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 72 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux Solvent Free DW Coating Grey and Red'. Factory applied, light grey or red coloured epoxy coatings. Apply as per manufacturer's data sheet number '558', revision '04', dated October 2022. Cure for 7 days@30°C. For use with water up to 30°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.
'TPU 2053, TPU 2054, TPU 2055, TPU 2056, TPU 2057 & TPU 2058'. Five layered, membrane systems manufactured by calendaring. The membranes consist of: 1.) a transparent polyurethane inner layer (in contact with the water), 2.) a tie layer, 3.) a reinforcing layer (PES or PA), 4.) a tie layer & 5.) a blue or beige coloured polyurethane outer layer (not in contact with the water). For use with water up to 23°C.
‘4158 – Discontinuous Aramtex® & lubricated PTFE’. White coloured, fibre packing material manufactured by braiding. For use with water up to 23°C. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Chesterton Style 455EU'. Blue coloured fibre/NBR material, manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'GRE-FPI-KSA-WAVISTRONG Pipe'. Light brown coloured (opaque), GRE pipe manufactured by helical winding. For use with water up to 85°C.
'Klüberbeta VR 67-17002'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Unisilkon L200'. White coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'YC-FM01'. Dark grey coloured, pressed and sintered Strontium Ferrite magnet. For use with water up to 85°C.
'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.
'Creta Pipe'. Grey coloured, extruded polybutylene pipe. For use with water up to 85°C.
'iFIT Pipe'. Multi-layered, extruded pipe comprising of a natural (off-white coloured) polyethylene inner layer, aluminium middle layer and white coloured, polyethylene outer layer. For use with water up to 85°C.
'Comisa EVO Pipe'. Extruded PE-RT/Al/PE-HD barrier pipe comprising of a white coloured PE-RT inner layer, aluminium middle layer and white coloured PE-HD outer layer. For use with water up to 85°C.
'ATLAS & FLOWTECH - PP-RGF PIPE'. Extruded, multi-layered pipe comprising of a green coloured PP-R inner layer, red coloured glass fibre middle layer and green coloured (with red stripe) PP-R outer layer. For use with water up to 85°C.
‘T-MECH’. Green coloured, extruded PP-R Pipe. For use with water up to 85°C.
`Mecflon Y2` thrust bearing. Black coloured, extruded PTFE thrust washer. For use with water up to 85°C.
'HQB1W Butyl Sealant'. White coloured, flexible butyl tape. Apply as per manufacturer's instructions. For use with water up to 85°C.
Page 194 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
