Range of electronically controlled ion exchange water softeners (salt regenerated) for commercial and domestic use. Maximum working pressure 5.0 bar. Cold water use
'ABS 727 White'. White coloured, injection moulded ABS material. For use with water up to 65°C.
'CER18635 Ceramic Ring'. White coloured (opaque), sintered, ceramic ring. For use with water up to 85°C.
'SIGMALINE 855 (11) Blue'. Factory applied, blue coloured, two-component polyurethane coating. 'SIGMALINE 855 (11) Blue' is for use with water up to 23°C. In September 2024 ‘SIGMALINE 855 (11) Off White’ was added to the approval. Off-white coloured two-component polyurethane coating. 'SIGMALINE 855 (11) Off White' is for use with water up to 36°C. Mix and apply as per manufacturer's Product Data Sheet ‘7656’, dated 'September 16, 2024'. Cure for 12 hours@20°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sheraplex Blue, Black, Green & Silver'. Factory applied, organic resin coating system, consisting of a primer and 'Delta Seal' topcoat (available in blue, black, green and silver colours). Apply one coat of primer (as per instructions: WI.BMC.W02 Issue 2 - February 2005) and cure for 2 and ½ hours at 380°C. Then apply a passivation layer through immersion for 15 minutes at 76-99°C (as per instructions: WI.BMC.W06 Issue 1 August 2004). Apply 1 topcoat of 'Delta Seal' (as per instructions WI.BMC.W01A Issue 2 August 2010) and cure for 20 minutes at 200°C. All are for use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CSJX53-2 Red'. Factory applied, red coloured polyacrylic resin coating. Apply as per manufacturer's instructions file no. ‘CSJ-0016-1’, version no. ‘A1’, dated 2016.10.12. Cure for 50 minutes@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'Interline 925P Light Grey & Interline 925P Off White'. Site applied, two component epoxy coatings. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's datasheet '10257', issue date '07/02/2022'. Cure for 7 days@25°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Nitocote EP405 (3821)’. Site applied, blue coloured, two component solvent free epoxy resin coating consisting of two bases (coat 1 base; Nitocote EP405 white & coat 2 base; Nitocote EP405 blue) & clear EP405 hardener. Mix parts A & B of each coat in a 100:13 weight ratio and apply in accordance with Fosroc data sheet issue 7 (CI/SfB: Pn6) dated November 2013. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rubber Lub-A3'. Orange/amber coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Klüberbeta VR 67-17002'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Polimid A 50 GF Natural WR'. Natural (appears off-white/beige), 50% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
'Polimid A 50 GF Black WR'. Black coloured, 50% glass fibre reinforced, injection moulded PA66 material. Between June 2023 and May 2025, the material was for use with water up to 23°C. From June 2025, the material is for use with water up to 85°C.
'Polimid A 30 GF Black WR'. Black coloured, 30% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
‘AL ZAMIL roto moulded tank panel’. White coloured, roto-moulded, multi-layered PE tank panel. For use with water up to 60°C.
‘AL ZAMIL blow moulded tank panel’. Pale blue coloured, blow-moulded, multi-layered PE tank panel. For use with water up to 60°C.
'KAN-therm ultraPRESS PERTAL'. White coloured, extruded PE-RT/Al/PE-RT pipe. For use with water up to 65°C.
'Kimplas Trustlene PE100 Electro-fusion fittings'. Black coloured, injection moulded Electro-fusion fittings. For use with water up to 65°C.
'Smart Joint Fitting'. Blue coloured, injection moulded HDPE fittings. For use with water up to 60°C.
Page 173 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
