'NP-PET 00N'. Natural (appears white in colour), extruded PET mesh screen. For use with water up to 70°C.
‘Tecotek OP20 GR10 NL 01 0A QF, Tecotek OP20 GR20 NL 01 0A QF & Tecotek OP20 GR30 NL 01 0A QF’. ‘Tecotek OP20 NL 01 0A QF’ was added to the approval in November 2023. Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
‘FILTER NOZZLES P, PTL, P5, P6, P7, T, TTL, TD, R, RTL, RD, B, V, VL, C, D4, D3 & D9. NUTS N & HR. EXPANDING BOLT TS. VALVE BODIES DPI & DPS. SLEEVES G, GM & GE. COLLECTORS CSI05, CSI06, CST06, CSD06, CSI08, CST08, CSG08, CSD08 & CSI08. FILTER ARMS SF/SFC, SD, SB & SC. FILTER NOZZLES RB2 & RB3. DISTRIBUTORS RBD2 & RBD3’. Blue, black, dark grey, light grey, green, red, yellow & light blue coloured, injection moulded polypropylene components. For use with water up to 23°C.
‘Verplen C30 01 NE ACLKUV (black coloured), C30 04 NE ACLUV (black coloured), C30 08 NE ACLKUV (black coloured) & C30 08 NT ACLKUV (natural – appears beige coloured)’. Injection moulded, glass filled polypropylene materials. For use with water up to 60°C.
'F801'. White coloured, extruded PTFE material. For use with water up to 85°C.
'F1500'. White coloured, extruded PTFE material. For use with water up to 85°C.
'INOLUB™ T201F, T202F, T203F, T204F & T205F'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
`Soltane F/B 197`. White coloured, extruded thermoplastic polyurethane material. For use with water up to 60°C.
'X-Treme Tape'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EP12/2/5 BLK 'O'-rings & seals'. Black coloured, injection moulded EPDM 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
‘4280’ black coloured injection moulded EPDM rubber components. Shore hardness 80. '4280 Membrane' has a tested in-radius size of 1.75mm. ‘4280 ’O’ rings’ have a tested in-radius size of 1.31mm. ‘4280 washers’ have a tested in-radius size of 1.05mm. All components are for use with water up to 85°C.
'D0012'. Black coloured, EPDM rubber material manufactured by vulcanised moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'HW-EPDM SH 50'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 65°C.
'SIL50 RED 'O' rings & seals'. Red coloured, injection moulded silicone 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.3mm. The seals have a tested in-radius size of 4.2mm. For use with water up to 85°C.
'Gebatout2'. Green coloured, polymer sealing paste. Apply as per manufacturer's instructions, 'version 11' dated 23/09/19. For use with water up to 85°C.
'RC 50'. Purple coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'40810813 (3019 THF Free)'. Colourless (transparent) solvent cement. Apply as per manufacturer's fact sheet 'TDS00481' dated 20th July 2018. Cure for between 24 hours and 21 days@7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Astral PVC Gel'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions review date '2019-09-11'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of stop valves with plastic bodies and an EPDM diaphragm. The valves are operated via a switch located on the valve. The RCL and RPL models can also be operated by a remote switch. The product incorporates a plastic strainer central to the body. All valves are for use with copper pipe (manufactured to BS EN 1057). The PL suffix valves are also for use with PEX pipe (manufactured to BS7291-3). Models added Jan 2025 are for use with PE80 & PE100 pipes manufactured to BS EN 12201:2 at the inlets and the outlets are suitable for PEX pipe manufactured in accordance with BS7291 and copper pipe manufactured in accordance with BS EN 1057. For above ground use only. Maximum working pressure 10.0 bar. Cold water use only.
Page 172 of 578
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
