'EP7041F'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AN004LFG'. Black coloured, compression moulded Ebonite rubber material. Shore hardness 75. Tested in-radius size 2.6mm. For use with water up to 23°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
'SYC3 0825 S30CB04 Boot'. Black coloured, compression moulded silicone rubber boot component. Shore hardness 30. The component has an irregular shape with a tested in-radius size of between 0.6mm & 1.2mm. For use with water up to 85°C.
'MXLOC 12638, 38 & 48'. Green coloured acrylic based adhesives. Apply as per manufacturer`s instructions. For use with water up to 23°C.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'‘Welding polymer for Kryoclim®️, Girair®️ and HTA (formerly known as GIRPI HTA Fusion THF Free'. Site applied, orange coloured solvent cement, intended to join PVC-C pipe and fittings. Apply as per pages 4.2 & 4.3 of 'Durapipe HTA®' technical data sheet '04900200 February 2013'. Cure for 24 hours at 7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Floor mounted, single hole, single outlet (swivel) combination tap assembly (brass bodies - in various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working Pressure 10 bar. Maximum operating Temperature 60 °C
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, electronically operated tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve and actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose connection incorporates a stainless-steel strainer. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of side or bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with two test ports. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body and EPDM gaskets and seal rings. For insertion into specifically dimensioned bores Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of ceramic cartridge headworks and ceramic disc diverter headworks with plastic bodies, EPDM and/or silicone seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM O rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 169 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
