'5308400500 polypropylene liner tube', taupe coloured, injection moulded polypropylene liner. In March 2025, '5308400500 polypropylene liner tube', natural (appears beige), injection moulded polypropylene liner was added to the approval. In March 2026, ‘5308400500 polypropylene liner tube’, grey coloured, injection moulded polypropylene liner was added to the approval. For use with water up to 23°C.
'PTFE G439'. Terracotta coloured, extruded PTFE sealing ring. For use with water up to 85°C.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'M534 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'M534 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Guarri 543'. Blue coloured pipe sealant. Apply as per manufacturer's instructions '543 Usage', version '0', issue date '22/06/2023'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Drei Bond 5204’. Yellow coloured anaerobic adhesive paste. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
‘THERMOLAST DW’ range of natural (appears off-white), black, white & grey coloured, extruded TPE-S materials with an in-radius between 0.39mm & 0.41mm. DW7HTV-(1) (70 ShA). DW7HTU-(1) (75 ShA). DW8HTV-(1) (80 ShA). DW8HTU-(1) (85 ShA). DW9HTV-(1) (90 ShA). DW0HTV-(1) (40 ShD). (1) – indicates the colour of the material: - LCNT: means without pigment (natural colour). - 9017: means black coloured material. - 9003: means white coloured material. - 7---: 4 digit code means grey coloured material, mixture of white and black pigments. For use with water up to 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically operated tap assemblies incorporating stainless-steel bodies (various finishes - see model). Flow is controlled via solenoid valve and actuated by a capacitive (TSL-881/883) or infra-red (TSL-882/884) sensor. The products can also be supplied with an additional plastic aerator (from a choice of two). Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) electronically controlled combination tap assemblies (brass bodies – chrome plated). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating on the side of the body. The spout outlets incorporate plastic flow straighteners. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The products are supplied with single lever spherical valves. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Side entry BS1212-4 fill valves with a plastic body. Maximum working pressure 10.0 bar. Coldwater use only.
Type ‘AB’ air gap arrangements (verified by test - suitable for backflow protection against fluid category 5) consisting of an inlet hose and solenoid valve on the inlet supply. Maximum working pressure 10.0 Bar Maximum operating temperature 55.0°C
Thermostatic cartridge with NBR ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout is a pull-out spray type incorporating a push button and plastic aerator. The connection to the pull-out hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar. Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets of all models except TAP031 incorporate a plastic aerator. TAP031L Maximum working pressure - 5.0 Bar. Maximum operating temperature 85°C. All other models Maximum working pressure - 10.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a single sequential headworks with single lever type operating members. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2). Maximum working pressure 5 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination taps assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure: See models. Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 bar Maximum operating temperature 60°C
Single hole, single outlet (fixed) combination basin tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Page 162 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
