‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELEC GRP PIPE B'. Yellow coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'SHUANGSHI GRP PIPE 51160'. Yellow coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'PROTEAN Silicone Paste'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Denyl 66 3010 Natural F' & 'Denyl 66 3010 Black F'. Natural (appears off-white) and black coloured, injection moulded, Polyamide 66 materials. For use with water up to 65°C.
'EPLAMID 66 GFS 30 FW NC'. Natural (appears beige), injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
'EPLAMID 66 GFS 30 FW BK'. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
'TEGA PE100 fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'Stars Water Tank Panel'. Multi-layered, roto-moulded LLDPE/PE foam panel comprising of a white (opaque) water contact layer, off-white (translucent) second layer, black (opaque) third layer and white (opaque) outer layer. For use with water up to 65°C.
'DERINSU PE100 Fitting'. Black coloured, injection moulded PE100 fitting. For use with water up to 60°C.
'UNIDELTA Electrofusion Fitting'. Black coloured, injection moulded PE100 Electrofusion Fitting. For use with water up to 60°C.
'Cosmoplast Butt Fusion Fitting'. Black coloured, polyethylene butt-fusion fitting. For use with water up to 60°C.
'Wefatherm Fitting'. Green coloured, injection moulded PP-R fitting. For use with water up to 60°C.
'Wefatherm Pipe'. Green coloured (with or without blue external stripe), extruded PP-R pipe. 'Wefatherm Fibre Pipe'. Extruded, multi-layered pipe comprising of a green coloured PP-R inner layer, green coloured PP-R/fibre middle layer and green coloured (with red stripe) PP-R outer layer. Both pipes are for use with water up to 60°C.
'Aquatherm Fitting'. Green coloured, injection moulded polypropylene fittings. For use with water up to 60°C.
'Innopol CS 4-8000 G'. Grey coloured, compression moulded polypropylene material. For use with water up to 60°C.
'UW61424 & UW61427 – Instinct'. White coloured, extruded PTFE tapes. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'EPNER-4665'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 50°C.
Page 149 of 442
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
