Range of single and dual flush WC outlet valves. The valves incorporate an internal overflow and are operated with one push button (single flush) or two push buttons (dual flush). Cold water use only.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2306096

Size:

10.1283 - 1 1/2" or 2" BSP (M).

Marking:

Plumb Bliss & PB logo on body

Installation Requirements:

R001 R571 R581

Expiry date:

30/06/2028

Model:

10.1283 Dual Flush Valve

Approval Holder:

Bliss UK Group Ltd

Company Name

Bliss UK Group Ltd

Address

Unit 4A Kinsbourne Farm Wick End Stagsden Bedfordshire

Postcode

MK43 8TS

Country

United Kingdom

Phone

01234 860230

General Email

accounts@blissukgroup.co.uk

View All Listings by this Company

‘Zip Aquapoint IV’ range of wall mounted directly heated unvented storage vessels (cased and insulated) incorporating an enamel lined cylinder and safety kit. The cylinder is factory fitted with a temperature and pressure relief valve (7.0 bar/90°C) and a drain valve. The product is supplied with an installation kit comprising of an expansion vessel, tundish and an inlet manifold incorporating a 6.0 bar expansion relief valve, an adjustable pressure reducing valve with stainless-steel strainer (adjustable between 2.7 and 3.3 bar, but pre-set at 3.0 bar), and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The compression connections of the installation kit are for use with copper pipe (Manufactured to EN 1057). Maximum working pressure 5.5 bar. Maximum operating temperature 70°C. Cold supply only.

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

250502703

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Aquapoint iV models: ½” BSP (M) inlet and outlets. AQ105 and AQ0108 Installation kits: 22mm compression.

Marking:

Zip on front panel. Zip company logo, model, capacity and other technical information on adhesive label on cylinder body casing.

Installation Requirements:

R001 R511

Expiry date:

31/05/2030

Model:

AP430S - 30 Ltr Direct, AP450S - 50 Ltr Direct, AP480S - 80 Ltr Direct, AP4100S - 100 Ltr Direct. All products are supplied with an installation kit, either AQ105 (AP430S and 450S models) or AQ108 (AP480S and AP4100S models).

Approval Holder:

Zip Heaters UK Ltd T/A Zip Water UK

Company Name

Zip Heaters UK Ltd T/A Zip Water UK

Address

Trafalgar House, Trafalgar Business Park, Dereham

Postcode

NR19 1JG

Country

United Kingdom

Phone

0345 600 5005

General Email

sebastian.ducker@zipwater.co.uk

View All Listings by this Company

Range of screwed gland cock valves with bronze bodies and a hose union outlet connection. Maximum working pressure: 10 Bar. Maximum operating temperature: 100°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP male x 14mm hose union ¾” BSP male x 20mm hose union 1” BSP male x 27mm hose union

Marking:

Boss, GM, H and size on body

Installation Requirements:

R001 R040

Expiry date:

31/12/2030

Model:

BOSS 81HU

Approval Holder:

BSS Industrial

Company Name

BSS Industrial

Address

Travis Perkins PLC Ryehill House Rye Hill Cose Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

Manufacturer:

Y.S. Valve Manufacturing Co. Ltd.

Company Name

Y.S. Valve Manufacturing Co. Ltd.

Address

General Email

View All Listings by this Company

Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.

Section:

1530 Miscellaneous Fittings

Size:

see model

Marking:

GENEBRE on the flexible connection. GENEBRE, DN, connection type & length on label on product On the flange: DIN PN 10/16 1.0038

Installation Requirements:

R001

Expiry date:

31/10/2026

Model:

2831 07 (DN32), 2831 08 (DN40), 2831 09 (DN50), 2831 10 (DN 65), 2831 11 (DN80), 2831 12 (DN100), 2831 13 (DN 125), 2831 14 (DN150).

Product Images

Approval Holder:

Genebre, S.A

Company Name

Genebre, S.A

Address

Poligono Industrial Pedrosa, Avinguda Joan Carles I, 46 – 48, Edificio GENEBRE Hospitalet de Llobregat

Postcode

08908

Country

Spain

Phone

(+34) 93 298 80 00

General Email

cazorla@genebre.es

View All Listings by this Company

Range of ‘SureCal’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

RT – 1.1/4” BSP (M) to 2.1/4” BSP (M) RF – 48 mm OD

Marking:

'SureCal' logo, Model, Voltage, Size and other information on label.

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

Model Code: XXYZS Where XX denotes the boss type and can be replaced with any of the following: RT = Thread Type RF = Flange Type Where Y denotes the heating tube material and can be replaced with any of the following: 1 = Copper 2 = AISI 304 / AISI 304L 3 = AISI 321 4 = AISI 316 / AISI 316L 5 = Alloy 800 / Alloy 825 / Alloy 840 6 = Titanium 7 = AISI 309S 8 = AISI 310 Where Z denotes the brazing system and can be replaced with any of the following: A = Tin Alloy B = Silver Alloy C = Itek Brazing Where S denotes the surface enamelling and can be replaced with either of the following: S = Enamelled Blank = Not Enamelled

Approval Holder:

Thermowatt S.p.A.

Company Name

Thermowatt S.p.A.

Address

Via San Giovanni Battista 21 Arcevia

Postcode

60011

Country

Italy

Phone

+39 0731988246

General Email

thermowatt@legalmail.it

View All Listings by this Company