Range of spherical valves (nickel plated) brass bodies with single lever operating members, (chromium plated) brass ball and PTFE seat. Maximum working pressure 40.0 bar (Models 124-1027 CST, 124-1028 CST and 124-1029 CST) Maximum working pressure 25.0 bar (Models 124-1030 CST and 124-1031 CST) Maximum working pressure 16.0 bar (Models 124-1032 CST and 124-1033 CST) Maximum operating temperature 85°C.
Range of inline and angled screwdriver or lever handle operated spherical valves with (chromium plated) brass bodies, chromium plated brass ball, NBR ‘O’-rings. For use with copper pipe manufactured to EN 1057 Maximum working pressure 16.0 bar at 30°C and 5 bar at 99°C Maximum working pressure 6.0 bar. Maximum operating temperature 90°C (model TX480 only)
Range of spherical valves with either chrome plated brass, nickel-plated brass, or brass bodies (See models) with a chrome plated brass ball and PTFE seats. Models TS-1212, TS-1202, TS-1101, TS-1201 and TS-1111 have lock shields, models TS-1271, TS-3012, TS-3001, TS-2001 and TS-2042 have lever operating members Maximum working pressure 25 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of undercounter and passthrough commerical dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). The inlet hose incorporates a stainless steel strainer. Maximum working pressure 4.0 bar. Maximum operating temperature 55°C.
Range of polyphosphate scale inhibitors comprising of an inline (nickel plated) brass body and head, and a separate cartridge with an aluminium body and plastic cap. Maximum working pressure 5.0 bar. Cold water use only.
Range of UV disinfection units incorporating 316L stainless steel bodies and quartz sleeves. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply as per manufacturer’s technical data sheet 'no. 786.3' dated 2013-V2'. Cure for 5 hours@23°C or 30 minutes@50°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac Two-Pack Epoxy Blue – 746 & Jerlac Two-Pack Epoxy Red – 747'. Factory applied, blue or red coloured, two-component epoxy coatings. Mix resin and hardener in a 3:1 volume ratio and apply as per manufacturer's instructions. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF4300'. Nitrile rubber/aramid fibre, calendered material which is white coloured on one side and green coloured on the other side. For use with water up to 23°C.
'Extrastrong SMC/ESF-30-10' pipe. Natural (appears pale green coloured) GRE pipe manufactured by filament winding. For use with water up to 70°C.
'Zytel® RSFG30G50L BK595'. Black coloured, injection moulded glass fibre reinforced nylon (polyamide 610) material. For use with water up to 85°C.
'Zytel® FG70G30HSR3 BK309'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'Tecomid NB40 GR30 NL HC QW'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'4MID 9B22130 W-A BNL100'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
Page 13 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
