Range of combined pre-set temperature and pressure relief valves incorporating Bronze body, DZR brass seat and plunger, EPDM ‘O’-rings, PTFE seal and silicone diaphragm. The valves incorporate a manually operated lever easing gear. The valves are factory pre-set between 0.7 bar and 12.5 bar. Maximum operating temperature 90°C. Maximum working pressure between 0.7 bar and 12.5 bar. Maximum operating temperature 90.0°C
Range of BOSS 958 combined pre-set temperature and pressure relief valves incorporating Bronze body, DZR brass seat and plunger, EPDM ‘O’-rings, PTFE seal and silicone diaphragm. The valves incorporate a manually operated lever easing gear. The valves are factory pre-set between 0.7 bar and 12.5 bar. Maximum operating temperature 90°C. Maximum working pressure between 0.7 bar and 12.5 bar. Maximum operating temperature 90.0°C
Combined temperature and pressure relief valve incorporating DZR bronze body, and a rubber silicone seat washer. Compression fittings for use with copper to BS EN 1057. Maximum working pressure 7.0 Bar Maximum operating temperature 95.0°C
Range of non-return, swing gate valves with brass bodies and brass discs with a NBR gasket. . Maximum working pressure 16.0 bar or 20.0 bar. Maximum operating temperature 85°C.
Range of blue epoxy coated ductile iron gate valves with an EPDM coated ductile iron wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. Electrolytic models have a maximum operating temperature of 40°C. Magnetic models are cold water use only.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. 403342 & 403359 Electrolytic models have a maximum operating temperature of 40°C. 403328 & 403335 Magnetic models are cold water use only.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. Electrolytic models have a maximum operating temperature of 40°C. Magnetic models are cold water use only.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply at a Relative Humidity of below 60% as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the RH & curing conditions that appear on the approval. If the RH and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rocar S2'. Grey coloured, sintered & pressed silicon carbide 'faucet disc' component. For use with water up to 85°C.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Super Poxy 505TL'. Factory applied, grey coloured, two-component Epoxy coating. Mix Parts A & B in a 100:20 weight ratio and apply as per manufacturer's TDS dated '2026.01.14'. Cure for 24 hours@20°C. For use with water up to 23°C.
'IF1947T'. Factory applied, red coloured Fusion Bonded Epoxy coating. Apply as per manufacturer's Instructions for Use 'Doc. No. SPPR/L3/WI/PRD/28.' Cure for 45 minutes@220°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat FBE Red RAL 3013' (red coloured) & 'Eco Coat FBE Blue RAL 5017' (blue coloured). Factory applied Epoxy coatings. Apply as per manufacturer's Instructions for Use 'Doc. No.:SPPR/L3/WI/PRD/28A'. Cure for 45 minutes@220°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Bondstrand GRE Fittings - MYSN'. Black coloured GRE fittings manufactured by filament winding. For use with water up to 85°C.
'PT-100' Grease. White coloured (opaque), non-miscible grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Plustek PA7001G7BK11'. Black coloured, injection moulded polyamide material. For use with water up to 85°C.
'Prime Plastic Industries HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'SOFTPEX V® hose inliner'. Off white coloured (translucent), extruded polyethylene hose. For use with water up to 70°C.
'Qingfa PE100 Black Pipe Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
Page 12 of 15
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
