'JSGL-BFSC III B (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-SRC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'R579 TP13582 BLACK & R579 TP14619 BLACK'. Black coloured, rotomoulded PE materials. For use with water up to 85°C.
‘NORYL’ black coloured, grey coloured or beige coloured, injection moulded PPE + PS materials. FE1410PW – 73701. FE1520PW – 73701. FE1630PW – 73701. FE1740PW – 73701. FE1520PW - 4G8B5291. FE1630PW - 4G8B5291. FE1410PW – 7G8B4911. FE1520PW – 7G8B4911. FE1630PW – 7G8B4911. FE1410PW-4G8B5291, FE1740PW-4G8B5291 & FE1740PW-7G8B4911 were added to the approval in April 2025. For use with water up to 85°C
'Hostalen PP H2142 12'. Black coloured, injection moulded and compression moulded polypropylene material. For use with water up to 23°C.
'EP011470P(KAWN)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'N146 Sealing Cap and Bellow'. Black coloured, injection moulded nitrile rubber sealing cap & bellow. Shore hardness 70. The cap has a tested in-radius size of 0.6mm and the bellow has a tested in-radius size of 1.0mm. For use with water up to 23°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Bidet seat where the flow is controlled via a solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum operating pressure 10 bar. Maximum operating temperature 40°C.
Page 110 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
