'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2303534

Expiry date:

31/03/2028

Approval Holder:

KUBOTA Corporation

Company Name

KUBOTA Corporation

Address

1-3, Kyobashi 2-chome, Chuo-ku Tokyo, 104-8307

Country

Japan

Phone

+81-90-2492-1627

View All Listings by this Company

'A/W AQUA (A) Epoxy 100'. Site applied, pale straw coloured epoxy/linseed oil waterproof coating. Apply as per manufacturer's Technical Document 'FSQP-707-05' dated '2021.01.04'. Cure for 6 hours under UV light (wavelength 365μm) at a distance of 150mm. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2302557

Expiry date:

29/02/2028

Approval Holder:

FRSI Corp.

Company Name

FRSI Corp.

Address

No.315. Knowledge Industry Center, JEONNAM TECHNOPARK, 13, Yulchonsandan 4-ro, Haeryong-myeon, Suncheon-si, Jeollanam-do

Country

Korea, Republic of

View All Listings by this Company

‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2303536

Expiry date:

31/03/2028

Approval Holder:

Master Builders Solutions Construction Chemicals LLC

Company Name

Master Builders Solutions Construction Chemicals LLC

Address

PO Box 37127, Dubai Investment Park, Phase 1 Expo Road, Dubai

Country

United Arab Emirates

View All Listings by this Company

'Thoenes BA120'. Blue coloured fibre/NBR material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.

Section:

5075 Fibre

Section Subtitle:

These materials are for use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

WRAS Approval Number:

2010577

Expiry date:

31/10/2025

Approval Holder:

Thoenes Dichtungstechnik GmbH

Company Name

Thoenes Dichtungstechnik GmbH

Address

Zeppelinstrabe 1, D-01665 Klipphausen

Country

Germany

View All Listings by this Company

'Thoenes BA110'. Green coloured NBR/fibre material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

Section:

5075 Fibre

Section Subtitle:

These materials are for use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

WRAS Approval Number:

2010578

Expiry date:

31/10/2025

Approval Holder:

Thoenes Dichtungstechnik GmbH

Company Name

Thoenes Dichtungstechnik GmbH

Address

Zeppelinstrabe 1, D-01665 Klipphausen

Country

Germany

View All Listings by this Company