'Powercron® 6070 B coating'. Factory applied, black coloured resin based coating. Apply as per manufacturer's TDS 'CR607B/CP588B'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AF-300 B Pro'. Blue coloured, NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio
'Tesnit® BA-GL & Tesnit® BA-GL3000'. Green/blue coloured fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'Polypipe Silicone Spray Lubricant SG 300'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 2', dated 'November 2022'. For use with water up to 85°C.
'RADILON® S RV350RKC2 306 BK'. Black coloured, injection moulded, 35% glass fibre reinforced, PA6 material. For use with water up to 85°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'Drei Bond 5330'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
‘Grilamid TR 30 natural, TR 30 LS natural (appear colourless, translucent), TR 30 LS blue 4345, TR 30 LS blue 4387 & TR 30 LS blue 4396 (blue coloured)’. Injection moulded, PA 61/X materials. For use with water up to 85°C.
Range of wall mounted shower kits. Comprising of brass bodied wall mounted shower outlet, shower hose and handsets (various finishes), incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60*C
Range of hand showers and shower arm kits with (brass bodies - various finishes. The inlets of the hand showers and the inlet elbows incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Open outlet use only. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH72 | 1/2" | 6 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH73 | 1/2" | 6 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH62 * | 1/2" | 6 bar | 65 °C | Waterworks | Body and tile guard | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH63 * | 1/2" | 6 bar | 65 °C | Waterworks | Body and tile guard | No | Not applicable | Not Applicable | Not Applicable |
Product Identification(s) with an * as suffix = models added 11/08/2025
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies models HVDCVC-31, HVDCVC-32 are chrome plated. Maximum working pressure 16 Bar Maximum operating temperature 60°C
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 812003A | 23.8mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812038A | 23.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812049A | 19mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812056 | 18.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812057 | 19.0mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812072 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812073 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812114 | 18.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30D-9 | 29.91mm | 10 bar | 85 °C | WANHAI, WRAS, 30D-9, Production date (DD/MM/YYYY) | Body | No |
Page 101 of 108
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
