Valves

Section Code 2240 : Solenoid, plastic.

Back To Directory Sections

#2004052

Ranges of solenoid valves with plastic bodies, incorporating EPDM ‘O’-rings and diaphragms. Models also incorporate a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only. From September 2020, the maximum operating temperature is 90.0°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2004052
Expiry date:
30/04/2025
Size:
See Model
Marking:
Robertshaw, ENEC and other technical info on metal housing.
Installation Requirements:
R001 R008
Model:
VAI FC series: 3/8”, ½”, ¾” BSP (M) inlet & outlet. SAD-E FC series: ¾” BSP (M) inlet x 10mm spigot outlet. ASD FC series: ¾” BSP (M) inlet x 10mm spigot outlet. V18, V19, V28, V29, V38, V39, V48 & V58 series: ¾” BSP (M) inlet x 10mm or 13mm spigot outlet.
Approval Holder:
Robertshaw S.R.L.
Company Name
Robertshaw S.R.L.
Address
Via Giacomo Matteotti, 62 Cinisello Balsamo, 20092 Milano
Country
Italy

View All Listings by this Company
Manufacturer:
Robertshaw S.R.L.
Company Name
Robertshaw S.R.L.
Address
Via Giacomo Matteotti, 62 Cinisello Balsamo, 20092 Milano
Country
Italy

View All Listings by this Company

Print This Approval


#2007365

Range of normally closed (monostable) and pulse controlled/latching (bistable) solenoid valves with plastic bodies, integral stainless steel strainer, From September 2023 the 50.005.101 model can also be supplied with an integral plastic strainer. EPDM diaphragm, EPDM ‘O’-rings and seals. To be installed in specifically dimensioned bodies. The 50.005.101 model can be supplied with or without a brass adaptor. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2007365
Expiry date:
31/07/2025
Note:
The 19.00x.287 model is not approved in its own right.
Size:
See model
Marking:
A.u.K. Müller, size, pressure and technical information on adhesive label on body.
Installation Requirements:
R001 R008
Model:
50.005.101: M22x2. thread on valve housing 50.009.101: M29x1.5 thread on valve housing. Both models utilise model 19.00x.287 as a pilot valve for the servo controlled part
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2011023

Normally closed solenoid valve with a plastic body and EPDM diaphragm. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2011023
Expiry date:
30/11/2025
Size:
1/8” BSP (F)
Marking:
ODE, size and technical information on body.
Installation Requirements:
R001
Model:
21JP1R1E23-WRT0
Approval Holder:
ODE S.r.l.
Company Name
ODE S.r.l.
Address

View All Listings by this Company
Manufacturer:
ODE S.r.l.
Company Name
ODE S.r.l.
Address

View All Listings by this Company

Print This Approval


#2009330

Range of plastic bodied normally closed latching solenoid valves. The 42424000 model is supplied with an additional brass housing. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2009330
Expiry date:
30/09/2025
Size:
See model
Marking:
Grohe, product no., ident code and production date (WW/YY) on adhesive label on body.
Installation Requirements:
R001 R008
Model:
42424000: 8.50mm ID Manifold 42399000: M22x1
Approval Holder:
Grohe AG
Company Name
Grohe AG
Address
Industriepark Edelburg 58675 Hemer
Country
Germany
Phone
02372 930
General Email
info@grohe.com

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2012013

Non latching solenoid valve with a plastic body and an EPDM gasket and ‘O’-ring. Maximum working pressure 8.0 bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2012013
Expiry date:
31/12/2025
Size:
½” BSP (M)
Marking:
Kangleda on bracket on solenoid .
Installation Requirements:
R001 R008
Model:
FCD.3
Approval Holder:
Zhejiang Kangleda New Energy Co., Ltd.
Company Name
Zhejiang Kangleda New Energy Co., Ltd.
Postcode
CHINA

View All Listings by this Company
Manufacturer:
Zhejiang Kangleda New Energy Co., Ltd.
Company Name
Zhejiang Kangleda New Energy Co., Ltd.
Postcode
CHINA

View All Listings by this Company

Print This Approval


#2101039

Solenoid valves with a plastic body and silicone diaphragm and ‘O’ rings. Maximum working pressure 8.0 bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2101039
Expiry date:
31/01/2026
Size:
½” BSP (M)
Marking:
CEME, model and date of manufacture (DD/MM/YYYY) on adhesive label on body.
Installation Requirements:
R001 R008
Model:
Series L L40050LSP00L6V & L50050LSP00L6V.
Approval Holder:
Ceme SpA
Company Name
Ceme SpA
Address
VIALE DELL’INDUSTRIA, 5 TRIVOLZIO
Postcode
27020
Country
Italy
General Email
info@cemegroup.com

View All Listings by this Company
Manufacturer:
Deca Srl.
Company Name
Deca Srl.
Address
General Email

View All Listings by this Company

Print This Approval


#2012360

Range of normally closed solenoid valves with a plastic body and silicone rubber diaphragm & ‘O’-rings. Models ending ‘007’ have a maximum working pressure of 0.25 bar. All other models have a maximum working pressure of 0.06 bar. Maximum operating temperature 90°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2012360
Expiry date:
31/12/2025
Size:
12mm O.D. x 10.07mm O.D. spigot. 15.04mm O.D. x 15.08mm O.D. spigot. 18.98mm O.D. x 17mm O.D. spigot.
Marking:
A.u.K Müller, model type, date of manufacture (WW/YY) and other technical information on coil. A.u.K Müller logo on body.
Installation Requirements:
R001 R008
Model:
40.006.111. 40.008.111. 40.012.111. 46.006.111. 46.008.111. 40.006.114. 40.008.114. 46.006.114. 46.008.114. 40.006.116. 40.008.116. 46.006.116. 46.008.116. 40.006.117. 40.008.117. 46.006.117. 46.008.117. 46.008.118. 40.008.101. 40.012.101. 46.008.101. 40.008.151. 46.008.151. 40.012.151. 40.008.104. 46.008.104. 40.008.154. 46.008.154. 40.012.191. 40.014.111. Where: 40 = solenoid type, either MS.026 for 40.006/008.XXX models, or MS.006 for 40.012/014.XXX models. 46 = solenoid type, MS.006. 006-012 = Orifice size in mm (DN) of valve seat, e.g. 006 = 6mm. 1st X = number of valves in a row: 1 for 40.012/014.XXX models, 1-5 for all other models. 2nd x = PTFE Valve seat: 0 = No, 1 = Yes, 5 = valve with regulated breather and PTFE seat, 9 = solenoid operated with pulsed voltage and PTFE seat (start with Un and then pulsed to reduce power consumption) 3rd X = Speciality: 1 = Valve housing and outlet moulded in one piece, 4 = Valve housing with detachable outlet, 6 = Banking valve with detachable outlet, 7 = Banking valve with valve housing and outlet moulded in one piece, 8 = Single chamber valve with special inlet and membrane. Example code: 46.008.114 = MS.006 type, single chamber solenoid valve with DN 8 valve seat orifice, PTFE valve seat and detachable outlet.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2101053

Range of bistable (all models) or monostable/normally closed (19.00x.287 only) solenoid valves with either a plastic body (19.00X.287) or plastic internal body with stainless steel threaded casing (50.005.102 and 50.005.(050) models) with EPDM diaphragms and ‘O’-rings. Maximum working pressures: 50.005.(050) model: 8.0 bar. All other models: 10.0 bar. Maximum operating temperature 70°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2101053
Expiry date:
31/01/2026
Size:
Please refer to model.
Marking:
A. u. K. Müller, model number, manufacturing date (WW/YY) & technical information on adhesive label on body.
Installation Requirements:
R001 R008
Model:
50.005.(050): M20. 50.005.102: M20. 19.00X.287: OD 7.5mm.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2103020

Solenoid valve with plastic body and silicone rubber diaphragm. Maximum working pressure 0.18 Bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2103020
Expiry date:
31/03/2026
Size:
15.9mm Hose spigot connection (inlet and outlet).
Marking:
Deltrol Controls, model, DoM (YYWW) and other technical information on adhesive label on body. Deltrol control and flow arrow on body.
Installation Requirements:
R001
Model:
DSVP12N-2LSXH-240M
Approval Holder:
Deltrol Controls (USA)
Company Name
Deltrol Controls (USA)
Address
2740 So. 20th Street Milwaukee WI 53215
Country
United States

View All Listings by this Company
Manufacturer:
Deltrol Controls (Vietman)
Company Name
Deltrol Controls (Vietman)
Address
29 Street 2 Vietman Singapore Ind Park Thuan An Town Binh Duong Province Vietnam 72000

View All Listings by this Company

Print This Approval


#2104329

Range of solenoid valves with plastic bodies and EPDM diaphragms. The inlet incorporates a plastic strainer and an integrated flow meter sensor. Both the inlet and the outlet incorporate a white plastic flow restrictor. The products are also supplied with an optional EPDM outlet gasket, for installation over the outlet spigot. Maximum working pressure 10.0 bar (to diaphragm). Maximum operating temperature 85°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2104329
Expiry date:
30/04/2026
Note:
Open outlet use only.
Size:
See model.
Marking:
TP Reflex logo, model no, pressure range and flow arrow on body.
Installation Requirements:
R001 R008
Model:
¾” BSP (M) inlet/10.27mm spigot outlet: ES90/88. ES180/88. ESL 90/88-M. ¾” BSP (M) inlet/10.27mm double outlet: ED90/88. ED180/88. EDL90/88-L. ED180/88-L. ED180/88-FM. EDL90/88–M. ¾” BSP (M) inlet/10.27mm triple spigot outlet: ET90/88. ET180/88. ETL90/88-M. 23.64mm manifold inlet/9.10mm spigot outlet: 1ES-L. ¾” BSP (M) inlet/10.27mm quadruple spigot outlet EQL90/88-L: ¾” NPT (M) double inlet/12.81mm spigot outlet: EM180/88.
Approval Holder:
TP Reflex Group S.p.A
Company Name
TP Reflex Group S.p.A
Address
Via Brescia 8, Tradate (VA)
Country
Italy
Phone
0331 816611
General Email
info@tp-spa.com

View All Listings by this Company
Manufacturer:
TP Reflex Polska Sp. zo.o & TP Reflex Group S.p.A (Italy)
Company Name
TP Reflex Polska Sp. zo.o & TP Reflex Group S.p.A (Italy)
Address
General Email

View All Listings by this Company

Print This Approval


#2103317

Range of plastic bodied solenoid valves incorporating a stainless steel spring and armature with an EPDM diaphragm. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2103317
Expiry date:
31/03/2026
Size:
1/4” BSP (F) inlet/outlet.
Marking:
Robertshaw, model and other technical information on coil. Direction of flow arrow on body.
Installation Requirements:
R001 R008
Model:
126F9001 (SF9001)
Approval Holder:
Robertshaw (China) Controls Company Limited
Company Name
Robertshaw (China) Controls Company Limited
Address
No 16-7 Xianshan East Road, Qingdao Electronic Information Industrial Park, Chengyang District
Country
China

View All Listings by this Company
Manufacturer:
Robertshaw (China) Controls Company Limited
Company Name
Robertshaw (China) Controls Company Limited
Address
No 16-7 Xianshan East Road, Qingdao Electronic Information Industrial Park, Chengyang District
Country
China

View All Listings by this Company

Print This Approval


#2012081

Range of normally closed and normally open plastic solenoid valves with EPDM ‘O’-rings and sealing rings. Pushfit connections for use with John Guest LLDPE pipe or copper pipe. The 47.004.103 model acts as a diverter between two outlets, where one outlet is always open. Maximum working pressures see model section. Maximum operating temperatures: 65°C - 47.00X.1XX models with John Guest LLDPE pipe only. 90°C - 47.004.103 model with John Guest LLDPE pipe only. Models added January 2021: Cold water use only - 47.00X.2XX (4mm & 8mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm & 8mm) with copper pipe only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2012081
Expiry date:
31/12/2025
Size:
See model.
Marking:
AUK Muller, technical information and date of manufacture (WWYY) on adhesive label on body.
Installation Requirements:
R001 R008
Model:
47.002.102 (NC - Normally Closed): 6mm pushfit - 8.0 bar. 47.002.102 (NC - Normally Closed): 8mm pushfit - 8.0 bar. 47.002.182 (NO - Normally Open): 8mm pushfit - 7.0 bar. 47.004.102 (NC - Normally Closed): 6mm pushfit - 3.5 bar. 47.004.102 (NC - Normally Closed): 8mm pushfit - 3.5 bar. 47.004.103 (NC - Normally Closed) 3/2 Way: Nozzle 7mm - 3.5 bar. Models added January 2021: 47.002.202 (NC - Normally Closed): 8mm pushfit - 8.0 bar. 47.003.202 (NC - Normally Closed): 8mm pushfit - 5.0 bar. 47.003.203 (NC - Normally Closed): 4mm pushfit - 5.0 bar. 47.003.203 (NC - Normally Closed): 6mm pushfit - 3.0 bar. 47.003.203 (NC - Normally Closed): 8mm pushfit - 3.0 bar. 47.004.202 (NC - Normally Closed): 6mm pushfit - 3.0 bar. 47.004.202 (NC - Normally Closed): 8mm pushfit - 3.5 bar. 47.004.282 (NO - Normally Open): 6mm pushfit - 3.0 bar. 47.004.203 (NC - Normally Closed): 6mm pushfit - 3.0 bar. 47.004.203 (NC - Normally Closed): 8mm pushfit - 3.0 bar.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2109352

Aquatsop leak detection system intended to shut the water supply in the event of a water leak. Consisting of two single normally closed servo controlled solenoid valves with a flow regulator and stainless steel filter at the inlet. A LDPE inner hose with corrugated plastic outer hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2109352
Expiry date:
30/09/2026
Note:
This product has not been tested or approved for leak detection or anti-flooding claims made by the approval holder.
Size:
¾” BSP(F) plastic inlet nut with 10mm ID hose outlet.
Marking:
A.u.K Muller, voltage, temp, model type and date of manufacture (WW/YY).
Installation Requirements:
R001 R008
Model:
Aquastop 13.007.226
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2110013

Range of latching and normally closed (see model) solenoid valves with plastic bodies, NBR diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2110013
Expiry date:
31/10/2026
Size:
M24 (M)
Marking:
Serie Micro, RPE website, minimum and maximum working pressure, and technical specifications on top of valve body.
Installation Requirements:
R001 R008
Model:
MICRO Series: Latching - 3, 4.5 & 6V Normally Closed - 12V.
Approval Holder:
R.P.E. Srl.
Company Name
R.P.E. Srl.
Address
Via S. Abrogio, 1,3,5 22070 Carbonate (CO) Italy
Phone
+39 0331.832515

View All Listings by this Company

Print This Approval


#2112328

Solenoid valve incorporating a plastic body and an EPDM diaphragm. The product incorporates a plastic flow regulator with an EPDM washer, and a plastic filter on the inlet. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2112328
Expiry date:
31/12/2026
Size:
¾” BSP (M) inlet x 12mm spigot outlet.
Marking:
Robertshaw and ENEC on adhesive label on coil. Flow arrow, and PN on body.
Installation Requirements:
R001 R008
Model:
127F019.
Approval Holder:
Robertshaw (China) Controls Company Limited
Company Name
Robertshaw (China) Controls Company Limited
Address
No 16-7 Xianshan East Road, Qingdao Electronic Information Industrial Park, Chengyang District
Country
China

View All Listings by this Company
Manufacturer:
Robertshaw (China) Controls Company Limited
Company Name
Robertshaw (China) Controls Company Limited
Address
No 16-7 Xianshan East Road, Qingdao Electronic Information Industrial Park, Chengyang District
Country
China

View All Listings by this Company

Print This Approval


#2201343

Solenoid valve with a plastic body, EPDM membrane and plastic or stainless steel strainer. From March 2023 the product may also be supplied with a Ø 28.61mm x ¾” BSP (M) plastic adaptor. From December 2023 the product may also be supplied with a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Non-metallic materials and components comply with BS6920 at 70°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2201343
Expiry date:
31/01/2027
Size:
Ø 28.61mm. Size added March 2023: ¾” BSP (M).
Marking:
50.007.120 model: AuK Muller, logo, type, size and pressure rating on adhesive label on body. 50.007.120 + plastic adaptor variant added March 2023: A.u.K. Muller and flow arrow on body. A.u.K. Muller, size, voltage, pressure range and date of production (WW/YY) on adhesive label on body.
Installation Requirements:
R001 R008
Model:
50.007.120
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2201306

Range of solenoid valves with a plastic body and an EPDM diaphragm. Available as either inline (126 suffix models) or 90° outlet (115 suffix models). The inlet of the existing 62.009.115 (¾” BSP (M) inlet x ⅜” BSP (M) outlet) model incorporates a plastic strainer and a plastic flow regulator. The products are also supplied with an optional stainless-steel strainer for installation on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperatures: Existing model 62.009.115: ¾” BSP (M) inlet x ⅜” BSP (M) outlet: 90°C. Models added November 2023: Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2201306
Expiry date:
31/01/2027
Size:
See model.
Marking:
Existing model: AuK Muller, date of manufacture (WWYY), model number and other technical information on coil. AuK Muller logo, flow arrow, date of manufacture (WW/YY) on housing. Models added November 2023: AuK Muller, AuK Muller logo, model, QR code, orifice size, pressure rating, date of manufacture (WWYY) and other technical information on coil. AuK Muller logo and flow arrow on housing.
Installation Requirements:
R001 R008
Model:
62.009.115: ¾” BSP (M) inlet x ⅜” BSP (M) outlet. Models added November 2023: 62.005.115: ⅜” or ½” or ¾” BSP (M) inlet x hose-nozzle outlet. 62.005.126: ⅜” or ½” BSP (M) inlet x ⅜” BSP (M) or hose-nozzle outlet. 62.007.115: ½” or ¾” BSP (M) inlet x hose-nozzle outlet. 62.007.126: ½” or ¾” BSP (M) inlet x ½” or ¾” BSP (M) or hose-nozzle outlet. 62.009.115: ½” or ¾” BSP (M) inlet x hose-nozzle outlet. 62.009.126: ½” or ¾” BSP (M) inlet x ½” or ¾” BSP (M) outlet.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2203030

Plastic bodied solenoid valve available as both a latching and normally closed variant, with an EPDM diaphragm and ‘O’-rings. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2203030
Expiry date:
31/03/2027
Size:
¾” BSP (M) inlet/outlet.
Marking:
CISTERMISER on adhesive label on coil. Flow arrow and DF/15 on body.
Installation Requirements:
R001
Model:
DFV
Approval Holder:
Cistermiser Ltd
Company Name
Cistermiser Ltd
Address
Unit 1 Woodley Park Estate, 59/69 Reading Road Woodley
Postcode
RG5 3AN
Country
United Kingdom
General Email
jake.felstead@cistermiser.co.uk

View All Listings by this Company
Manufacturer:
Cistermiser Ltd
Company Name
Cistermiser Ltd
Address
Unit 1 Woodley Park Estate, 59/69 Reading Road Woodley
Postcode
RG5 3AN
Country
United Kingdom
General Email
jake.felstead@cistermiser.co.uk

View All Listings by this Company

Print This Approval


#2104349

‘1175B’ range of servo-controlled normally closed (NC), normally open (NO) or latching solenoid valves with off-white nylon bodies, incorporating a NBR diaphragm with POM diaphragm inserts. For use with copper tube manufactured to EN1057 or John Guest Speedfit barrier pipe manufactured to BS7291 part 3. Maximum working pressure 10.0 bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2104349
Expiry date:
30/04/2026
Size:
15mm pushfit.
Marking:
Beta valve on adhesive label on body.
Installation Requirements:
R001 R008
Model:
1175BC (normally closed). 1175BA (normally open). 1175BB (latching).
Approval Holder:
Beta Valve System Ltd.
Company Name
Beta Valve System Ltd.
Address
Park House Business Centre Desborough Road High Wycombe Bucks.
Postcode
HP12 3DJ
Country
United Kingdom
Phone
01494 459511
General Email
sales@betavalve.com

View All Listings by this Company
Manufacturer:
Beta Valve System Ltd.
Company Name
Beta Valve System Ltd.
Address
Park House Business Centre Desborough Road High Wycombe Bucks.
Postcode
HP12 3DJ
Country
United Kingdom
Phone
01494 459511
General Email
sales@betavalve.com

View All Listings by this Company

Print This Approval


#2207034

Range of latching and non-latching solenoid valves with a plastic body (all models, except for 07230017 & 07230018 models added September 2023) and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2207034
Expiry date:
31/07/2027
Size:
½” BSP (M) inlet/outlet. Models added September 2023: M28x1
Marking:
Model number, technical specifications, and date of manufacture (WW/YY) on adhesive label on solenoid assembly. Stern Logo on solenoid assembly. Flow arrow on inline plastic body (applicable models).
Installation Requirements:
R001
Model:
07221116: LSA3WPC ASSY Latching, 07221104: LSA6WPC ASSY Latching, 07221129: LSA9C ASSY Latching, 07221118: LSA9WPC ASSY Latching, 07221112: NCA6WPC ASSY Non-Latching, 07221107: NCA9WPC ASSY Non-Latching, 07221113: NCA12WPC ASSY Non-Latching, 07221110: NCA24WPC ASSY Non-Latching. Models added September 2023: 07230018: LSA9C ASSY Latching (Solenoid assembly + Diaphragm only), 07230017: LSA9WPC ASSY Latching (Solenoid assembly + Diaphragm only).
Approval Holder:
Y. Stern Engineering (1989) Ltd
Company Name
Y. Stern Engineering (1989) Ltd
Address
15 Gan Rave Blvd 8122217 Yavne ISRAEL

View All Listings by this Company

Print This Approval


#2209328

Premix control unit for an infrared sensor tap comprising of a solenoid valve with plastic body, EPDM diaphragm and ‘O’-rings, and silicone seals. Both the cold and hot inlets incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The central section of the valve incorporates a plastic strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2209328
Expiry date:
30/09/2027
Size:
½” BSP (M).
Marking:
QTOO (brand of D Line) on outer casing
Installation Requirements:
R001 R008 R010
Model:
QSF01
Approval Holder:
D Line
Company Name
D Line
Address
Jylingevej 59, kld Copenhagen
Postcode
2720
Country
Denmark
Phone
+4572170138
General Email
rik@dline.com

View All Listings by this Company

Print This Approval


#2210359

Bistable (latching - pulse controlled) or monostable (normally open) solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. The products incorporates a stainless-steel filer on the inlet. From February 2024 the product may also be supplied with a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature: Between October 2022 and January 2024 this product is suitable for hot water use only (70°C). From February 2024 to the end of October 2027 this product is suitable up to 70°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2210359
Expiry date:
31/10/2027
Size:
M28x1, M29x1,5.
Marking:
A.u.K. Müller, pressure range, type (M - monostable, B - Bistable), indent code, model no., voltage and date of production (WW/YY) on adhesive label on body. M28 size models also include DN size: DN7.
Installation Requirements:
R001 R008
Model:
50.007.101.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2211333

Normally closed (monostable) or latching (bistable) solenoid valve with a plastic body, EPDM membrane and ‘O’-rings, for insertion into specifically dimensioned bores. The inlet incorporates a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2211333
Expiry date:
30/11/2027
Size:
OD 7.5mm
Marking:
A.u.K Muller, model type, orifice size, pressure range, identification code, production date (WW/YY), and either B or M (B = Bistable/M = Monostable) on adhesive label on body.
Installation Requirements:
R001 R008
Model:
50.005.850
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2207081

Latching solenoid valves with a plastic body and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.

Non-metallic materials and components comply with BS6920 at 65°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2207081
Expiry date:
31/07/2027
Size:
½” BSP (M) inlet/outlet.
Marking:
Stern, date of manufacture (WW/YY) on adhesive label on body. Stern Logo and flow arrow on body.
Installation Requirements:
R001
Model:
Electroflo latching solenoid valve
Approval Holder:
Thomas Dudley Limited
Company Name
Thomas Dudley Limited
Postcode
DY1 4SJ
Country
United Kingdom
Phone
0121 530 7053
General Email
jcresswell@thomasdudley.co.uk

View All Listings by this Company

Print This Approval


#2305302

Range of bistable solenoid valves with plastic bodies, incorporating chrome plated brass inlets and outlets, stainless steel springs, and EPDM diaphrams and ‘O’-rings. Maximum working pressure 10.0bar. Maximum operating temperature 65°C

Non-metallic materials and components comply with BS6920 at 65°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2305302
Expiry date:
31/05/2028
Size:
see model.
Marking:
TCK (trademark of Xiamen OLT Co.,Ltd.) on body.
Installation Requirements:
R001 R008
Model:
V00001-1: ½” BSP (M) x ½” BSP (M). V00001-2: ½” BSP (M) x 7.02mm OD spigot connection.
Approval Holder:
Xiamen OLT Co., Ltd.
Company Name
Xiamen OLT Co., Ltd.
Address
No.950, Tonglong 2nd Road, Xiamen Torch High-tech Zone (Xiang'an) Industrial Zone, Xiamen City
Country
China

View All Listings by this Company
Manufacturer:
Xiamen OLT Co., Ltd.
Company Name
Xiamen OLT Co., Ltd.
Address
No.950, Tonglong 2nd Road, Xiamen Torch High-tech Zone (Xiang'an) Industrial Zone, Xiamen City
Country
China

View All Listings by this Company

Print This Approval


#2305319

Range of plastic solenoid valves with an EPDM membrane. 50.007.806.001 models incorporate a stainless steel strainer on the inlet. 50.007.806.003 models with a captive nut or ⅜” BSP (M) inlet incorporate a combined plastic washer and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C (50.007.806.001 & 50.007.806.002 models) and 65°C (50.007.806.003 models).

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2305319
Expiry date:
31/05/2028
Size:
see model
Marking:
A.u.K. Müller, pressure, size and date of manufacture (WW/YY) on adhesive label on body.
Installation Requirements:
R001 R008
Model:
50.007.806.001: ½” BSP (M) inlet and outlet, 50.007.806.001: ¾” BSP (M) inlet and outlet, 50.007.806.002: clamp connection 15.23mm (ID) inlet and outlet DN20 (OD), 50.007.806.003: ⅜” captive nut inlet x ⅜” BSP (M) outlet, 50.007.806.003: ⅜” BSP (M) inlet x ½” BSP (M) outlet, 50.007.806.003: ½” captive nut inlet x ⅜” BSP (M) outlet.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2306331

Range of solenoid valves with plastic bodies and EPDM rubber diaphragms. The inlet incorporates an inner and outer plastic strainer, EPDM washer and a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2306331
Expiry date:
30/06/2028
Size:
¾” BSP (M) inlet x 12mm spigot outlet.
Marking:
Hongchang, model, production date: YYYMMMDDD on adhesive label on body. Pressure rating and flow arrow on body.
Installation Requirements:
R001 R008
Model:
FCD, FCE, FCS, FPD, FPE, FPM, FPS ranges: Type nomenclature: FXYZU X denotes angle between inlet and outlet tube: C (vertical), P (parallel). Y denotes construction of fluid channel: D (single channel), S (double channels), E (triple channels), M (quadruple channels). Z denotes direction of coil assembly spade terminals, indicated as angle value between the spade terminals and the inlet (in degrees): 45, 90, 135, 180, 225, 270, 315, 360. When nomenclature Y = “D” - one value provided. “S” - two values provided. “E” - three values provided. A hyphen is provided between multiple values to indicate the direction of each coil assembly in a counterclockwise direction. e.g., FCE90-225-45G. U denotes optional series number: A - Z or blank, or 0, 1, 2, 3, 4 etc. (this does not affect the water pathway construction).
Approval Holder:
Zhejiang Hongchang Electrical Technology Co.,Ltd.
Company Name
Zhejiang Hongchang Electrical Technology Co.,Ltd.
Address
NO.258 South Shuanglin Street, Jinhua Industrial Zone, Zhejiang Province
Country
China

View All Listings by this Company

Print This Approval


#2306337

Range of solenoid valves with plastic bodies and EPDM diaphragms. The FD-160A, FD-160Z, FD-160B and FD-160P have brass inlet and outlets. The FD-138 and FD-160 prefix models incorporate a stainless steel strainers on the inlet. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2306337
Expiry date:
30/06/2028
Size:
FD138B: M10x1 All other models: ½” BSP (M) FD-139-6 model added September 2023: Outer dia. 16.5mm/Inner dia. 12.5mm.
Marking:
Fuxin, model no., voltage and date of manufacture (YYYY-MM-DD) on valve body.
Installation Requirements:
R001 R008
Model:
FD-138 series: 90 degree outlet: FD-138, FD-138-2. In-line offset outlet: FD-138B. In-line: FD-138E, FD-138E-2. FD-139 series: FD-139, FD-139B, FD-139-2, FD-139-4. FD-160 series: 90 degree outlet: FD-160AS, FD-160SZ, FD-160A, FD-160Z. In-line: FD-160BS, FD-160SP, FD-160B, FD-160P. Model added September 2023: FD-139-6.
Approval Holder:
Zhejiang Fuxin Electric Technology Co., Ltd.
Company Name
Zhejiang Fuxin Electric Technology Co., Ltd.
Address
368 Jingba Road, Yueqing Economic Development Zone, Wenzhou city, Zhejiang province
Country
China
General Email
www.china-fuxin.com/en

View All Listings by this Company
Manufacturer:
Zhejiang Fuxin Electric Technology Co., Ltd.
Company Name
Zhejiang Fuxin Electric Technology Co., Ltd.
Address
368 Jingba Road, Yueqing Economic Development Zone, Wenzhou city, Zhejiang province
Country
China
General Email
www.china-fuxin.com/en

View All Listings by this Company

Print This Approval


#2306065

Range of latching solenoid valves with plastic bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.

Non-metallic materials and components comply with BS6920 at 80°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2306065
Expiry date:
30/06/2028
Size:
1” BSP (M).
Marking:
Aquis logo (“Aquis”), product number, bistabil and voltage on adhesive label on body.
Installation Requirements:
R001 R008
Model:
60.001.138, 60.001.289.
Approval Holder:
Aquis Systems AG
Company Name
Aquis Systems AG
Address
Balgacherstrasse 17, 9445 Rebstein
Country
Switzerland

View All Listings by this Company
Manufacturer:
Aquis Systems AG
Company Name
Aquis Systems AG
Address
Balgacherstrasse 17, 9445 Rebstein
Country
Switzerland

View All Listings by this Company

Print This Approval


#2307325

Solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. The inlet incorporates a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2307325
Expiry date:
31/07/2028
Size:
M32.
Marking:
A.u.K. Müller, A.u.K. Müller logo, size, pressure, date of manufacture (WW/YY) and other technical information on adhesive label on the body.
Installation Requirements:
R001 R008
Model:
50.007.805 (monostable) & 50.007.805 (bistable/latching).
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2307348

Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2307348
Expiry date:
31/07/2028
Size:
21.56mm OD.
Marking:
TCK (trade-mark of Xiamen OLT Co., Ltd) on cover.
Installation Requirements:
R001 R008
Model:
V00002-A.
Approval Holder:
Xiamen OLT Co., Ltd.
Company Name
Xiamen OLT Co., Ltd.
Address
No.950, Tonglong 2nd Road, Xiamen Torch High-tech Zone (Xiang'an) Industrial Zone, Xiamen City
Country
China

View All Listings by this Company
Manufacturer:
Xiamen OLT Co., Ltd.
Company Name
Xiamen OLT Co., Ltd.
Address
No.950, Tonglong 2nd Road, Xiamen Torch High-tech Zone (Xiang'an) Industrial Zone, Xiamen City
Country
China

View All Listings by this Company

Print This Approval


#2309306

Range of normally closed solenoid valves with black or grey plastic bodfies, EPDM diaphragm and EPDM ‘O’-rings. The inlet incorporates a removable plastic strainer with a stainless steel mesh. The outlet incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2309306
Expiry date:
30/09/2028
Size:
18.02mm manifold connection
Marking:
TOTO on adhesive label on body.
Installation Requirements:
R001 R008
Model:
TOTO SV001, TOTO SV002, TOTO SV003.
Approval Holder:
TOTO Europe GmbH
Company Name
TOTO Europe GmbH
Address
Zollhof 2 40211 Düsseldorf Germany
Phone
+49 211 273080

View All Listings by this Company

Print This Approval


#2309037

Range of normally closed solenoid valves with plastic bodies and silicone diaphragms. Model DSVP12N-12LSX-240M has two inlets. Maximum working pressure 0.060 bar. Cold water use only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2309037
Expiry date:
30/09/2028
Size:
0.685” OD spigot.
Marking:
Deltrol controls, model, voltage, and other information on adhesive label on body.
Installation Requirements:
R001
Model:
DSVP12N-2LSX-240A, DSVP12N-2LSX-240M, DSVP12N-12LSX-240M, DSVP12N-2LSX-120B.
Approval Holder:
Deltrol Controls (USA)
Company Name
Deltrol Controls (USA)
Address
2740 So. 20th Street Milwaukee WI 53215
Country
United States

View All Listings by this Company
Manufacturer:
Deltrol Controls (USA)
Company Name
Deltrol Controls (USA)
Address
2740 So. 20th Street Milwaukee WI 53215
Country
United States

View All Listings by this Company

Print This Approval


#2310327

Range of normally closed solenoid valves with plastic bodies, EPDM ‘O’-rings and diaphragm. The inlet incorporates a combined plastic filter and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2310327
Expiry date:
31/10/2028
Size:
EV220T 14P GE E NC (042U8125 - GE) & EV220T 18P GE E NC (042U8175 - GE) models: ¾” BSP (M) x ¾” BSP (M). EV220T 14P GEH E NC (042U8105 - GEH) & EV220T 18P GEH E NC (042U8155 - GEH) models: ¾” BSP (M) x 20mm hose connection.
Marking:
Danfoss and flow arrow on body.
Installation Requirements:
R001
Model:
EV220T 14P GEH E NC (042U8105 - GEH). EV220T 14P GE E NC (042U8125 - GE). EV220T 18P GEH E NC (042U8155 - GEH). EV220T 18P GE E NC (042U8175 - GE). Where: GE = G3/4 External thread – G3/4 External thread. GEH = G3/4 External thread + Hose.
Approval Holder:
Danfoss A/S
Company Name
Danfoss A/S
Address
Nordborgvej 81 6430 Nordborg
Country
Denmark
Phone
+74 88 22 22
General Email
danfoss@danfoss.com

View All Listings by this Company
Manufacturer:
Danfoss Poland Sp. z o.o.
Company Name
Danfoss Poland Sp. z o.o.
Address
ul. Chrzanowska 5, 05-825 Grodzisk Mazowiecki
Country
Poland
General Email

View All Listings by this Company

Print This Approval


#2310306

Range of solenoid valves with plastic bodies and silicone membrane. Maximum working pressure 8.0 Bar. Maximum operating temperature 65°C.

Non-metallic materials and components comply with BS6920 at 65°C

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2310306
Expiry date:
31/10/2028
Size:
Size: DF065: ½” BSP (M) inlet/outlet, DF066: ¾” BSP (M) inlet/outlet, DF067: ⅜” BSP (M) inlet/outlet, DF062: ½” BSP (M) inlet/outlet, DF063: ¾” BSP (M) inlet/outlet, DF064: ⅜” BSP (M) inlet/outlet, DF054: ½” BSP (M) inlet/outlet, DF055: ¾” BSP (M) inlet/outlet, DF056: ⅜” BSP (M) inlet/outlet, DF061: ½” BSP (M) inlet x ⅜” BSP (M) outlet.
Marking:
Celec and flow arrow on body.
Installation Requirements:
R001 R008
Model:
DF065: Electro valve 6Vdc Bi stable ½” + Faston Solenoid, DF066: Electro valve 6Vdc Bi stable ¾” + Faston Solenoid, DF067: Electro valve 6Vdc Bi stable ⅜” + Faston Solenoid, DF062: Electro valve 6Vdc Bi stable ½” + Cable Solenoid, DF063: Electro valve 6Vdc Bi stable ¾” + Cable Solenoid, DF064: Electro valve 6Vdc Bi stable ⅜” + Cable Solenoid, DF054: Electro valve 6Vdc Bi stable ½” + Waterproof Solenoid, DF055: Electro valve 6Vdc Bi stable ¾” + Waterproof Solenoid, DF056: Electro valve 6Vdc Bi stable ⅜” + Waterproof Solenoid, DF061: Electro valve 6Vdc Bi stable ½” ⅜” + Waterproof Solenoid.
Approval Holder:
Ningbo Celec Electronic Co. Ltd.
Company Name
Ningbo Celec Electronic Co. Ltd.
Address

View All Listings by this Company
Manufacturer:
Ningbo Celec Electronic Co. Ltd.
Company Name
Ningbo Celec Electronic Co. Ltd.
Address

View All Listings by this Company

Print This Approval


#2311340

Range of plastic solenoid valves with an EPDM diaphragm and ‘O’-rings. The inlets incorporate a stainless-steel strainer (except for push fit inlet models). Push fit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. BS6920 70°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2311340
Expiry date:
30/11/2028
Size:
see model
Marking:
A. u. K. Müller GmbH & Co. KG logo and flow arrow on body. AuK Muller, model number, date of manufacture (MM/YY) and other technical informatrion on adhesive label on body.
Installation Requirements:
R001
Model:
51.005.125.xxx. Where xxx denotes inlet and outlet, and is replaced with: 001 = Inlet: Plug Ø 14,8mm and clamp x Outlet: Nozzle Ø 8,4mm with 1 ‘O’-ring. 002 = Inlet: Flange 11.07mm x Outlet: 6mm push fit. 003 = Inlet: Flange 11.07mm x Outlet: 8mm push fit. 004 = Inlet and outlet: 8mm push fit. 005 = Inlet and outlet: 6mm push fit. 006 = Inlet: Plug Ø 14,8mm and clamp/Outlet: Nozzle Ø 8,4mm with 2 ‘O’-rings. 008 = Inlet: Flange 11.07mm x Outlet: Nozzle Ø 8,4mm with 1 ‘O’-ring. 011 = Inlet: Plug Ø 14,8mm and clamp x Outlet: Nozzle Ø 8,4mm with 2 ‘O’-rings. 012 = Inlet: Flange 11.07mm x Outlet: Nozzle Ø 8,4mm with 2 ‘O’-rings. 022 = Inlet: Plug Ø 14,8mm and clamp x Outlet: 8mm push fit.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#2311363

Solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. Maximum working pressure 8.0 bar. Can only be used with water at 70°C. BS6920 70°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2311363
Expiry date:
30/11/2028
Size:
31 mm diameter (Push-in connector).
Marking:
A.u.K. Müller, model, voltage, power, orifice size, pressure rating article number, WRAS Approved Product logo and date of manufacture WW/YY on adhesive label on body.
Installation Requirements:
R001 R008
Model:
50.007.800.
Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval


#241004727

Range of monostable/normally closed pilot operated solenoid valves mounted in plastic bodies. Valve bodies can also be mounted together in multiples. Push-fit connections to be used with PTFE tube. Maximum working pressure 10 bar. Maximum operating temperature 70°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
241004727
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Expiry date:
31/10/2029
Size:
4mm or 6mm Pushfit.
Marking:
A. u. K. Müller GmbH & Co. KG and logo, type, 6V, DN and pressure rating on adhesive label on body. A. u. K. Müller GmbH & Co. KG logo, CE and date clock month & year moulded on body.
Installation Requirements:
R001 R008
Model:
19.Y1Y2.Z1Z2Z3 - Miniature valve Y1 = Function (1 = Distribution / 2 = Collection) Y2 = Pilot valve orifice size in mm (0,5- 1,2) Z1 = number of connected housing units Z2 = inlet connection; 1 = Nozzle (tube) / 2 = nozzle (push-fit) / 3 = Push-Fit (4mm) / 4 = Push-Fit (6mm) / 9 = Combination of multiple housings with Inlet 1-4 Z3 = outlet type; 1 = Nozzle (tube) / 2 = nozzle (push-fit) / 3 = Push-Fit (4mm) / 4 = Push-Fit (6mm) / 9 = Combination of multiple housings with Inlet 1-4
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0

View All Listings by this Company

Print This Approval


#240902713

Range of latching (LV), proportional (PV), servo (SV), pilot (EV) solenoid valves with natural (appear white), plastic bodies. Pushfit models are for use with John Guest LLDPE and DMFIT LLDPE pipes. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. All valves have a maximum working pressure of 10.0 bar. The bodies of valves with a silicone diaphragm are marked with an ‘S’ at the end of the model, e.g. ‘EV118/AS’ and have a maximum operating temperature 85°C. Valves with an EPDM diaphragm are for cold water use only and do not include this ‘S’ marking.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
240902713
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Expiry date:
30/09/2029
Note:
Valves with a black coloured body are not included on this approval.
Size:
Please refer to model.
Marking:
Hydra and model on body.
Installation Requirements:
R001 R008
Model:
EV - Standard (pilot operated) Solenoid Valve - Electrically Operated 220/240, 110/120 VAC. 24, 12 AC/DC LV - Latching (Bi-Stable) Solenoid Valve - Latching (Pulse) Operated 6, 12 VDC PV - Proportional Solenoid Valve - Proportional Operated 12, 24 VDC SV - Servo Solenoid Valve Servo Assisted 12 VDC KEY example – LV118/A LV – Valve type. Outlet number: XX1XX/X: one outlet XX2XX/X: two outlets XX3XX/X: three outlets Outlet angle: XXX18/X: 180 degrees (straight) XXX09/X: 90 degrees (elbow) Body type: XXXXX/xxnn: Variations: XX118/A (3/4" BSP x Ø11mm BARB) XX118/B (Ø3/8" x Ø3/8" PUSHFIT) XX118/C (3/8" BSP x 3/8" BSP) XX118/D (15mm COMPRESSION x 15mm COMPRESSION) XX118/E (3/4" BSP x 3/4" BSP) XX118/EB38 (3/4" BSP x 3/8" PUSHFIT) XX118/EB08 (3/4" BSP x 8mm PUSHFIT) XX118/EB06 (3/4" BSP x 6mm PUSHFIT) XX118/EB14 (3/4" BSP x 1/4" PUSHFIT) XX118/F (3/4" BSP x Ø10mm TUBE) XX118/FE (3/4" BSP x Ø3/8" TUBE) XX118/G (1/2" BSP x 1/2" BSP – SHORT THREAD -14.25MM) XX118/H (3/4" BSP x Ø6mm BARB) XX118/HP (3/4" BSP x Ø11mm BARB + SNAP BRACKET) XX118/HP14 (3/4" BSPM x 1/4" PUSHFIT + SNAP BRACKET) XX118/K (Ø8mm x Ø8mm PUSHFIT) XX118/L (Ø10mm x Ø10mm PUSHFIT) XX118/M (1/2" BSP x 1/2" BSP - LONG) XX118/N (Ø8mm x Ø10mm PUSHFIT) XX118/O (1/2" BSP x 1/2" BSP) XX118/P (Ø3/8" x Ø5/16" PUSHFIT) XX118/S (Ø8mm x Ø6mm PUSHFIT) XX118/T (Ø6mm x Ø6mm PUSHFIT) XX118/U (¼” JG x ¼” JG) XX118/J (3/4" BSP x Ø13mm BARB) XX109/B (3/4" BSP x Ø13mm BARB) XX109/D (3/8" PUSHFIT x 1/4" PUSHFIT) XX109/A (3/4" BSP x Ø11mm BARB) XX209/A (3/4" BSP x Ø11mm BARB) XX209/B (3/4" BSP x Ø13mm BARB) XX218/A (3/4" BSP x Ø11mm BARB) XX218/B (3/4" BSP x Ø10mm TUBE) XX218/C (3/4" BSP x Ø13mm BARB) XX218/D (3/4" BSP x Ø10mm TUBE + Ø11mm BARB) XX218/E (3/4" BSP x Ø3/8" PUSHFIT) XX218/HP (3/4" BSP x Ø11mm BARB + SNAP BRACKET) XX109/SA SAD VALVE (3/4" BSP x Ø11mm BARB) NOTES: Outlet Number: XX1XX/X: One Outlet XX2XX/X: Two Outlets XX3XX/X: Three Outlets Outlet angle: XXX18/X: 180 degrees (straight) XXX09/X: 90 degrees (elbow) Body Type: XXXXX/xxnn: Body type.
Approval Holder:
Hydralectric Group Ltd.
Company Name
Hydralectric Group Ltd.
Address
5 High Road, Byfleet, Surrey
Postcode
KT14 7QE
Country
United Kingdom
Phone
+44 1932 334 200
General Email
jamie.balkwill@hydralectric.com

View All Listings by this Company
Manufacturer:
EKI doo
Company Name
EKI doo
Address
Majer 27, 8340 Crnomelj
Country
Slovenia
General Email

View All Listings by this Company

Print This Approval


Show Per Page
5102050Show All

Back To Directory Sections

Page of 1

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.