Hansgrohe SE Approvals


#2003007

Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, multiple finishes), incorporating a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a rubber aerator and the products are supplied with a pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.

Section:
0450 Combination Tap Assemblies
Description:
Single hole tap with a single outlet and a fixed spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
No testing has been performed on the pop-up waste.
Size:
Stainless Steel braided PEX lined flexible hose assemblies with ⅜" BSP captive nut connections.
Marking:
AXOR on front of body.
Installation Requirements:
R001 R006 R009 R010
Expiry date:
31/03/2025
Model:
17 010 xxx 17 010 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers, as examples: 000 = chrome finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2003010

Wall mounted finish set with dome type operating member and a shower hose and handset (chromium plated brass). Outlet to shower incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 70°C

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Open outlet use only
Size:
½” BSP (M)
Marking:
AXOR on hand shower and shower hose
Installation Requirements:
R001 r040
Expiry date:
31/03/2025
Model:
10 651 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2003011

Wall mounted spout outlet (various finished brass, see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.

Section:
0682 Combination Tap Assemblies
Description:
Spout outlets.
Size:
¾” BSP (M).
Marking:
AXOR on face plate.
Installation Requirements:
R001 R040
Expiry date:
31/03/2025
Model:
12 417 xxx AXOR Starck Organic Bath spout. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers, as examples: 000 = chrome finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2003050

Wall mounted spout outlet with chromium plated brass body and EPDM ‘O’-rings. Incorporating a plastic aerator. Maximum operating temperature 60°C.

Section:
0682 Combination Tap Assemblies
Description:
Spout outlets.
Open outlet use only.
Size:
¾” BSP (M)
Marking:
AXOR on top of spout
Installation Requirements:
R001 R040
Expiry date:
31/03/2025
Model:
34 410 xxx AXOR Citterio M Bath spout Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2003052

Range of single hole, single outlet (swivel) combination tap assemblies (various finishes, see model), incorporating a quarter turn ceramic disc headwork with cross top or dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60 °C

Section:
0470 Combination Tap Assemblies
Description:
Single hole tap with a single outlet and a swivel spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
Size:
stainless steel braided PE-X lined flexible hose assemblies incorporating ⅜" BSP captive nut end connections.
Marking:
Hansgrohe on front of body
Installation Requirements:
R001 R006 R009 R010
Expiry date:
31/03/2025
Model:
71 280 xxx Logis M31 2-handle kitchen mixer 220 (Dome) 71 285 xxx Logis M32 Classic 2-handle kitchen mixer 220 (Cross) Model added February 2021: 71 283 xxx Logis M32 2-handle kitchen mixer 220 Eco Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD Stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2003057

Range of Single hole, single outlet (swivel) combination tap assemblies (various finishes, see model), incorporating quarter turn ceramic disc headworks with cross top (71 222, 71 270, 71 271 & 71 272) or dome (71 014, 71 122 & 71 221) type operating members. The spout outlet incorporates a plastic aerator. Certain models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C

Section:
0470 Combination Tap Assemblies
Description:
Single hole tap with a single outlet and a swivel spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
Size:
Stainless steel braided PE-X lined flexible hose assemblies with ⅜" captive nut end connections.
Marking:
Hansgrohe on front of tap body
Installation Requirements:
R001 R006 R009 R010
Expiry date:
31/03/2025
Model:
71 014 xxx Hansgrohe MyCube 2-handle basin mixer 150 with pop-up waste set. 71 122 xxx Hansgrohe MySport 2-handle basin mixer 150 with pop-up waste set. 71 221 xxx Hansgrohe Logis 2-handle basin mixer 150 without waste set. 71 222 xxx Hansgrohe Logis 2-handle basin mixer 150 with pop-up waste set. 71 270 xxx Hansgrohe Logis Classic 2-handle basin mixer 150 with pop-up waste set. 71 271 xxx Hansgrohe Logis Classic 2-handle basin mixer 150 LowPressure without waste set. 71 272 xxx Hansgrohe Logis Classic 2-handle basin mixer 150 with push-open waste set. available in -000 (Chrome) and customized finishes: -020 PVD polished chrome, -260 PVD brushed chrome, -830 PVD polished nickel, -820 PVD brushed nickel, -990 PVD polished gold optic, -250 PVD brushed gold optic, -300 PVD polished red gold, -310 PVD brushed red gold, -130 PVD polished bronze, -140 PVD brushed bronze, -330 PVD polished black chrome, -340 PVD brushed black chrome, -930 PVD polished brass, -950 PVD brushed brass, -800 PVD stainless steel optic.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2004021

Range of concealed, thermostatic blending valves (brass body). The flow is controlled via ‘detent’ (push to on push to off) headworks. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
2010 Shower Valves
Description:
Shower valve with thermostatic temperature control
The Hansgrohe iBox 01800180 is not covered by this approval.
Size:
Body for insertion into Hansgrohe iBox 01800180 (not supplied)
Marking:
AXOR on faceplate
Installation Requirements:
R001 R010 R040
Expiry date:
30/04/2025
Model:
36 707 xxx Axor ShowerSelect 36 715 xxx Axor ShowerSelect 36 723 xxx Axor ShowerSelect Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2004024

Range of shower handsets with chromium plated bodies. The products incorporate a strainer (stainless steel or plastic) at the inlet. All models, except 28 539 xxx, incorporate a plastic flow regulator at the inlet. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Open outlet use only. Claims of flow rate are made by the manufacturer and not considered part of the listing.
Size:
½” BSP (M).
Marking:
Hansgrohe, Croma and NF logo on body.
Installation Requirements:
R001 R040
Expiry date:
30/04/2025
Model:
28 535 xxx Hansgrohe Croma 100 Vario hand shower. 28 537 xxx Hansgrohe Croma 100 Vario hand shower EcoSmart 9 l/min. 28 536 xxx Hansgrohe Croma 100 Multi hand shower . 28 538 xxx Hansgrohe Croma 100 Multi hand shower EcoSmart 9 l/min. 28 539 xxx Hansgrohe Croma 100 Classic Multi hand shower. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2004026

Range of overhead shower outlets (various finishes) and concealed installation sets. Models 24 006 400, 24 016 400, 24 017 400, 35 281 xxx and 35 282 xxx incorporate a stainless-steel strainer on the inlet of and a plastic aerator on the shower head outlet. Maximum operating temperature 60°C

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Open outlet use only. The concealed installation sets are not approved in their own right.
Size:
½” BSP (M). ¾” BSP x ½” adapter.
Marking:
Hansgrohe on shower plate.
Installation Requirements:
R001 R040
Expiry date:
30/04/2025
Model:
Models for use with concealed installation set 24 010 180 Hansgrohe Rainmaker Select Basic: 24 006 400 Hansgrohe Rainmaker Select 460. 24 006 600 Hansgrohe Rainmaker Select 460. 24 016 400 Hansgrohe Rainmaker Select 460. 35 281 xxx AXOR ShowerSolutions Overhead shower 460/300. Models for use with concealed installation set 01800180: 24 007 400 Hansgrohe Rainmaker Select 460. 24 007 600 Hansgrohe Rainmaker Select 460. 24 017 400 Hansgrohe Rainmaker Select 460. 35 276 xxx AXOR ShowerSolutions Overhead shower 460/300. 35 282 xxx AXOR ShowerSolutions Overhead shower 460/300. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2004339

Thermostatic mixing valve with a brass body (chromium plated) with EPDM ‘O’-rings. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
2010 Shower Valves
Description:
Shower valve with thermostatic temperature control
Size:
⅜” captive nut x ⅜” BSP (M)
Marking:
Hansgrohe and date of manufacture (DDD.YYYY) on body
Installation Requirements:
R001 R010 R040
Expiry date:
30/04/2025
Model:
30 71 62 18

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2006045

Range of wall mounted shower outlets with brass bodies (various finishes). The 24 004 xxx, 24 014 xxx and 35 279 xxx models are supplied with ceiling mounted shower arm. The 24 005 xxx, 24 015 xxx, 35 275 xxx and 35 280 xxx supplied with wall mounted shower arm. The 24 005 xxx, 24 015 xxx, 35 275 xxx & 35 280 xxx models incorporate stainless steel strainers on the inlet. The 24 014 xxx & 24 015 xxx models incorporate plastic flow regulators on the inlet. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Marking:
24 004 xxx, 24 014 xxx, 24 005 xxx & 24 015 xxx models: Hansgrohe on faceplate. 35 275 xxx, 35 279 XXX & 35 280 xxx models: AXOR on faceplate.
Installation Requirements:
R001 R040
Expiry date:
30/06/2025
Model:
The following models are for use with the 24 010 180 Hansgrohe Rainmaker Select basic set overhead shower ceiling connector: 24 24 004 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower with ceiling connector 100 mm). 24 014 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower EcoSmart 9 l/ min with ceiling connector 100 mm). 35 279 xxx AXOR ShowerSolutions Overhead shower 460 / 300 (2jet with ceiling connector). The following models are for use with the 01 800 180 Basic set iBox universal: 24 005 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower with shower arm 450 mm). 24 015 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower EcoSmart 9 l/min with shower arm 450 mm). 35 275 xxx AXOR ShowerSolutions Overhead shower 460 / 300 (2jet with shower arm and softcube escutcheons). 35 280 xxx AXOR ShowerSolutions Overhead shower 460 / 300 (2jet with shower arm and square escutcheons). with rough 01800180 Where xxx denotes the surface finish, which can be replaced by any combination of numbers and/or letters. As examples, but not limited to: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2006331

Wall mounted concealed modular thermostatic mixing valve (brass body). The product is supplied with a shower hose and handset and incorporates additional outlet ports to supply shower outlet configuations controlled by push button flow control headworks. Primary flow control is via a half turn ceramic disc headwork and dome type operating member. The temperature is controlled independently via a thermostatic cartridge and dome operating member. Inlets incorporate stainless steel strainers and single check valve cartirgdes however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
2010 Shower Valves
Description:
Shower valve with thermostatic temperature control
Size:
¾” BSP (F) inlets & ½” BSP (F) outlets
Marking:
Axor on faceplate and shower handset.
Installation Requirements:
R001 R010 R040
Expiry date:
30/06/2025
Model:
46 700 xxx AXOR EdgeThermostatic module Select 470/100 for concealed installation for 2 functions 46 701 xxx AXOR Edge Thermostatic module Select 470/100 for concealed installation for 2 functions - diamond cut 18 310 180 AXOR Basic set for thermostatic module Select for 2 functions. 46 710 xxx AXOR Edge Thermostatic module Select 540/100 for concealed installation for 3 functions 46 711 xxx AXOR Edge Thermostatic module Select 540/100 for concealed installation for 3 functions - diamond cut 18 311 180 AXOR Basic set for thermostatic module Select for 3 functions. 46 720 xxx AXOR Edge Thermostatic module Select 610/100 for concealed installation for 4 functions 46 721 xxx AXOR Edge Thermostatic module Select 610/100 for concealed installation for 4 functions - diamond cut 18 312 180 AXOR Basic set for thermostatic module Select for 4 functions. 46 730 xxx AXOR Edge Thermostatic module Select 680/100 for concealed installation for 5 functions 46 731 xxx AXOR Edge Thermostatic module Select 680/100 for concealed installation for 5 functions - diamond cut 18 313 180 AXOR Basic set for thermostatic module Select for 5 functions. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2010701

Wall mounted bath spout incorporating a brass body (various finishes) and a plastic aerator. Maximum operating temperature 60°C.

Section:
0682 Combination Tap Assemblies
Description:
Spout outlets.
Marking:
AXOR on top of spout. Urquiola on underside of spout.
Installation Requirements:
R001 R040
Expiry date:
31/10/2025
Model:
11 430 xxx AXOR Urquiola Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples; 000 = Chrome optic finish, 800 = PVD stainless steel optic

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2008703

Wall mounted spout outlet (various finishes, see model) incorporating a plastic flow straightener. Maximum operating temperature 60°C.

Section:
0682 Combination Tap Assemblies
Description:
Spout outlets.
Size:
¾” BSP (M)
Marking:
Hansgrohe on spout
Installation Requirements:
R001 R040
Expiry date:
31/08/2025
Model:
15 412 xxx Hansgrohe PuraVida Bath spout Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish & 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2007054

Range of brass shower arms and plastic shower heads (various finishes) incorporating EPDM seals and ‘O’-rings, silicone seals and spray insert. The 26 469 xxx model is ceiling mounted & 26 470 xxx model is wall mounted. Both models incorporate a swivel joint housing a plastic flow regulator. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Open outlet use only. Claims for flow rate are made by the manufacturer and not considered part of the listing.
Size:
½” BSP (M)
Marking:
Hansgrohe on edge of body
Installation Requirements:
R001 R040
Expiry date:
31/07/2025
Model:
26 469 xxx HG Raindance Select S Overhead shower 240 2jet EcoSmart 9 l/min with ceiling connector. 26 470 xxx HG Raindance Select S Overhead shower 240 2jet EcoSmart 9 l/min with shower arm. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Product Images

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2007075

Range of single hole, single outlet (swivel) combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator and an on/off button which can stop the flow of water. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
0470 Combination Tap Assemblies
Description:
Single hole tap with a single outlet and a swivel spout. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
Size:
Stainless steel braided PE-X lined flexible hose assemblies with ⅜” captive nut end connections.
Marking:
Hansgrohe on body.
Installation Requirements:
R001 R006 R009 R010
Expiry date:
31/07/2025
Model:
72 820 xxx 72 825 xxx 73 854 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Product Images

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2006046

Range of overhead wall mounted shower outlets with brass bodies (various finishes), incorporating a plastic aerator and stainless-steel strainers on two of the three inlets to the main body. The 35 283 xxx models also incorporate plastic flow regulators on all three of the inlets to the main body. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Open outlet use only. The iBox 01800180 rough-in (concealed) set is not approved in its own right. Claims of flow rate are made by the manufacturer and not considered part of the listing.
Size:
¾” BSP (F)
Marking:
Hansgrohe on spray plate. AXOR on spray plate (model 35 283 xxx)
Installation Requirements:
R001 R040
Expiry date:
30/06/2025
Model:
24 001 400 Hansgrohe Rainmaker Select 580 3jet overhead shower (white/chrome). 24 001 600 Hansgrohe Rainmaker Select 580 3jet overhead shower (black/chrome). 24 011 400 Hansgrohe Rainmaker Select 580 3jet overhead shower Ecosmart 9 l/min (white/chrome). 35 283 xxx AXOR ShowerSolutions Overhead shower 250/580 3jet. All the above items are for use in conjunction with the iBox 01800180 rough-in (concealed) set. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2009001

Range of wall mounted concealed manual blending valves with a DZR brass body incorporating a ceramic cartridge headwork with a single lever operating member, fitting is available with trim set (available in various finishes). Maximum working pressure 10.0 bar. Maximum working temperature 70°C.

Section:
2000 Shower Valves
Description:
Shower valve with manual temperature control.
Rough in set 13 620 180 is not approved in its own right.
Size:
½” BSP (F)
Marking:
Hansgrohe on top of operating member. DR on body
Installation Requirements:
R001 R010 R040
Expiry date:
30/09/2025
Model:
31 686 xxx HG Metris 31 967 xxx HG Focus 71 606 xxx HG Logis 31 966 xxx HG Focus To be used with basic set 13 620 180 “xxx” denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and letters examples: 000= Chrome optic finish, 800= PVD Stainless steel optic finish
Product Images

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2009002

Wall mounted two hole, single outlet (swivel) combination tap assembly with DZR brass bodies (various finishes). Incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet incorporates a plastic aerator. Product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
0510 Combination Tap Assemblies
Description:
Two hole tap with a single outlet and a fixed spout.
For use with basic sets 13 622 180 (Models 34 112 xxx & 34 113 xxx) & 13 623 180 (Models 34 115 xxx & 34 116 xxx)
Size:
½” BSP (F)
Marking:
Axor (brand name of Hansgrohe) on spout
Installation Requirements:
R001 R010 R040
Expiry date:
30/09/2025
Model:
34 112 xxx AXOR Citterio M (167mm and plate) 34 113 xxx AXOR Citterio M (167mm and escutcheons) 34 115 xxx AXOR Citterio M (227mm and plate) 34 116 xxx AXOR Citterio M (227mm and escutcheons) Where xxx denote the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letter, as examples; 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Product Images

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#2009003

Range of overhead shower outlet and arm with chrome plated brass body. The inlet in model 27 375 000 incorporates a plastic flow regulator and stainless steel strainer. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
Description:
Shower heads and shower handsets
Open outet use only.
Size:
½” BSP (male)
Marking:
Hansgrohe on front of overhead shower face.
Installation Requirements:
R001 R040
Expiry date:
30/09/2025
Model:
27 370 xxx Hansgrohe Raindance E Overhead shower 240 1jet with shower arm 27 371 xxx Hansgrohe Raindance E Overhead shower 360 1jet with shower arm 24 cm 27 375 xxx Hansgrohe Raindance E Overhead shower 240 1jet EcoSmart 9 l/min with shower arm 27 376 xxx Hansgrohe Raindance E Overhead shower 360 1jet with shower arm 39 cm 27 381 xxx hansgrohe Raindance E Overhead shower 360 1jet with ceiling connector Where xxx denote the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letter, as examples; 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Product Images

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 1 of 21

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.