Range of DZR brass combination valves consisting of an in-line adjustable pressure reducing valve (2.1 - 16.0 bar for ILG22-2 model and 1.4 - 6.0 bar for all other models), a pressure relief valve (set @ 6.0 bar) and EPDM gaskets and ‘O’-rings. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 90°C.
Range of double regulating valves available with bronze bodies, incorporating a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'KOCETAL K100 GMP'. White coloured, injection moulded acetal material. For use with water up to 85°C.
'Super Poxy 505TL'. Factory applied, grey coloured, two-component Epoxy coating. Mix Parts A & B in a 100:20 weight ratio and apply as per manufacturer's TDS dated '2026.01.14'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Nitomortar TC2000'. Factory applied, two-component, grey coloured (once mixed and applied) epoxy resin sealing compound. The material is supplied in pre-weighed quantities (60% base, 40% hardener), to be applied in accordance with manufacturer's instructions 'FO SA/NITOMORTAR TC2000/0110/19'. Cure for 7 days@25°C and 55% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DUAYEN ANTIBLAST GEÇIRIMSIZ SPREY BOYA KAPLAMA'. Factory applied, two-component, black coloured (once mixed and applied), Polyurea coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's TDS 'Rev01', date of issue '22.04.2024'. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP TANK 500 PW'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a 3:1 volume ration and apply two coats as per manufacturer's TDS '0724'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate to 40°C and then spray apply as per manufacturer's instructions issued ‘March 2017, V4.1’. Cure for 20 minutes@180°C. For use with water up to 85°C.
‘Intergard 269’ primer for use with ‘Interline 975’ coating. Site applied, off-white coloured (once mixed and applied) epoxy coating system comprising of a two-part primer and two-part topcoat. Mix parts A & B of ‘Intergard 269’ primer in a 4:1 volume ratio and apply as per manufacturer’s TDS reference ‘206’, dated ‘11/03/2016’. Cure for 24 hours@10°C. Mix parts A & B of ‘Interline 975’ coating in a 2.2:1 volume ratio and apply as per manufacturer’s TDS reference ‘4236’, dated ‘04/02/2015’. Cure for 14 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 998 of 1045
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
