Directory Search Results

Print List

#2201522

'Interline 925 White'. Site applied, two-component, white coloured epoxy coating. Mix part A (off-white white coloured liquid) and part B (off-white coloured liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions ref. '2252', issue date 17/12/2020. Cure for 7 days@25°C. Between January 2022 and August 2022, the coating was for use with water up to 23°C. Between September 2022 and January 2027, the coating is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:
5042 Coatings, Paints & Linings
Section Subtitle:
Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.
WRAS Approval Number:
2201522
Expiry date:
31/01/2027

Approval Holder:
Akzo Nobel Saudi Arabia Ltd.
Company Name
Akzo Nobel Saudi Arabia Ltd.
Country
Saudi Arabia

View All Listings by this Company

Print This Approval


#2201515

'Aropol M 105 TA WRAS’ (formerly known as ‘Aropol M 105 TA’) & ‘Enguard GE NTRL HH WRAS’ (formerly known as ‘Enguard GE NTRL HH'): Translucent straw coloured (glossy one side textured the other), polyester laminating resin manufactured by hand lay-up & gelcoat (brush applied), sheet material. ‘Aropol M 105 TAXR’ & ‘Enguard GE WHI S WRAS’ (formerly known as ‘Enguard GE WHI S’): White coloured (glossy) on one side, translucent straw coloured (textured on the other), polyester laminating resin manufactured by hand lay-up & gelcoat (spray applied), sheet material. Apply as per Ineos Composites method statement ‘Preparation of laminated products for freshwater applications (WRAS)’, ‘code R071, edition 2’ dated 19.1.22. Cure for 9 hours at 23°C with 2% of MEKP-50 catalyst, post-cure for 24 hours@50°C and wash part thoroughly in water before use. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:
5125 Glass Reinforced Plastics (GRP)
Section Subtitle:
Material only. Components made from materials listed in this section may be required to be submitted for audit tests.
WRAS Approval Number:
2201515
Expiry date:
31/01/2027

Approval Holder:
Ineos Composites
Company Name
Ineos Composites
Address
Muovintie 35, 06850 Kulloo
Country
Finland

View All Listings by this Company

Print This Approval


#2208500

'S350 Silicone Fluid'. Colourless (transparent) silicone lubricant. Apply as per manufacturer's instructions for use 'LDAP-009', issue 1 dated May 2021. For use with water up to 85°C.

Section:
5160 Lubricants
Expiry date:
31/08/2027

Approval Holder:
Superior Seals Ltd.
Company Name
Superior Seals Ltd.
Address
Nimrod Way, Ferndown Industrial Estate, Ferndown, Dorset
Postcode
BH21 7SH
Country
UK
Phone
01202 854 300
General Email
sales@superiorltd.com

View All Listings by this Company

Print This Approval


#2110548

'Turbine Overmould 208399'. Black coloured, injection moulded, strontium ferrite filled nylon 6 component. For use with water up to 70°C.

Section:
5175 Nylon
Section Subtitle:
Components.
WRAS Approval Number:
2110548
Expiry date:
31/10/2026

Approval Holder:
Gems Sensors Inc.
Company Name
Gems Sensors Inc.
Address
1 Cowles Road, Plainville, CT 06062
Country
USA

View All Listings by this Company

Print This Approval


#2112516

'EcoPaXX® Q-DWX6 BK00002 & EcoPaXX® Q-DWX10 BK00002’ (black coloured). 'EcoPaXX® Q-DWX6 NA99001 & EcoPaXX® Q-DWX10 NA99001’ (natural – appears beige). Injection moulded polyamide materials. For use with water up to 85°C.

Section:
5180 Nylon
Section Subtitle:
Material only. Components made from materials listed in this section may be required to be submitted for audit tests.
WRAS Approval Number:
2112516
Expiry date:
31/12/2026

Approval Holder:
Envalior
Company Name
Envalior
Address
Flughafenstrasse 101, 40474 Dusseldorf
Country
Germany

View All Listings by this Company

Print This Approval


#2102546

'Sirogel 9000 (beige coloured) & Sirogel 9100 (white coloured)'. Manually injection moulded polyester resins. For use with water up to 45°C.

Section:
5217 Polyester
Section Subtitle:
Material only. Components made from materials listed in this section may be required to be submitted for audit tests.
WRAS Approval Number:
2102546
Expiry date:
28/02/2026

Approval Holder:
Saudi Industrial Resins Ltd
Company Name
Saudi Industrial Resins Ltd
Address
P O Box 7764 Jeddah 21472
Country
Saudi Arabia
Phone
+966-2-6518920
General Email
hesham@sir-ltd.com

View All Listings by this Company

Print This Approval


#2201506

Black coloured, compression moulded EPDM components. For use with water up to 85°C. ‘559843, 55985 & 559865’ ‘O’ rings. Shore hardness between 60 & 80. Tested in-radius sizes between 1.31mm & 3.49mm. ‘55985 Gasket’. Shore hardness 70. Tested in-radius size 1.0mm. ‘559865 gasket’. Shore hardness 80. Tested in-radius size 1.50mm. When processing an application for a Product Approval incorporating these components, these are the only shapes of components that are covered by the scope of the approval’.

Section:
5360 Rubbers
Section Subtitle:
Ethylene Propylene Diene Monomer (EPDM) - components.
WRAS Approval Number:
2201506
Expiry date:
31/01/2027

Approval Holder:
Eriks Group
Company Name
Eriks Group
Address
Toermmalijnstraat 5, 1812 RL Alkmaar, Postbus 280, 1800 BK Alkmaar
Country
Netherlands
General Email
info@eriks.com

View All Listings by this Company

Print This Approval


#2110543

'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.

Section:
5380 Rubbers
Section Subtitle:
Natural or Isoprene - material only.
WRAS Approval Number:
2110543
Expiry date:
31/10/2026

Approval Holder:
Pessina Angelo Srl.
Company Name
Pessina Angelo Srl.
Address
Via Veneziana Badalasco 73, 24045 Fara Gera d'Adda
Country
Italy

View All Listings by this Company

Print This Approval


#2110546

'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.

Section:
5380 Rubbers
Section Subtitle:
Natural or Isoprene - material only.
WRAS Approval Number:
2110546
Expiry date:
31/10/2026

Approval Holder:
Isoil Industria Spa
Company Name
Isoil Industria Spa
Address
Via F. lli Gracchi n.27, 20092 Cinisello Balsamo (MI)
Country
Italy

View All Listings by this Company

Print This Approval


#2201526

'7PD1612 washers'. Black coloured, extruded NBR rubber washers. Tested in-radius size 1.4mm. Shore hardness 70. '7PD1612 'O' rings'. Black coloured, injection moulded NBR rubber `O` rings. Tested in-radius size 0.9mm. Shore hardness 70. Both for use with water up to 60°C.

Section:
5390 Rubbers
Section Subtitle:
Nitrile (Acrylonitrile Butadiene) - components.
WRAS Approval Number:
2201526
Expiry date:
31/01/2027

Approval Holder:
Hutchinson Le Joint Francais
Company Name
Hutchinson Le Joint Francais
Address
ZI Ouest de Bazouges, Route de Craon, 53200 CHATEAU GONTIER
Country
France

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 100 of 408

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.