‘FLOGUL® 656 Bleu 5005’. Factory applied, blue coloured VOC paint. Apply as per manufacturer’s TDS dated ‘06/04/2022’. Cure for 7 days@20°C. For use with water up to 60°C.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2210549

Expiry date:

31/10/2027

Approval Holder:

BS Coatings

Company Name

BS Coatings

Address

Allee Paul Sabatier, BP 88, 27940 Aubevoye

Country

France

Phone

+ 33 32773077

View All Listings by this Company

'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5038 Coatings, Paints & Linings

Section Subtitle:

Site applied concrete coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2202569

Expiry date:

28/02/2027

Approval Holder:

Flexcrete Technologies Ltd.

Company Name

Flexcrete Technologies Ltd.

Address

Tomlinson Road, Leyland, Lancashire

Postcode

PR25 2DY

Phone

0845 2607005

General Email

Info@flexcrete.com

View All Listings by this Company

'DiChem Tiestop'. Site applied, grey coloured cementitious repair mortar. Mix 'DiChem Tiestop' and water in a mass ratio of 9.4:1 and apply as per manufacturer's instructions 'Rev 4, 02.22'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5063 Concrete, Cement and Mortar

Section Subtitle:

Repair materials. High humidity of 80% to 95% is required when curing cementitious materials.

WRAS Approval Number:

2102551

Expiry date:

28/02/2026

Approval Holder:

Direct Chemicals Ltd.

Company Name

Direct Chemicals Ltd.

Address

Unit 6, Stokes Farm, Binfield Road, Wokingham

Postcode

RG40 5PR

Country

Berkshire

Phone

0118 989 2666

General Email

sales@dichem.co.uk

View All Listings by this Company

'Teadit NA1006'. Green coloured NBR/fibre gasket material manufactured by mixing and calendaring. For use with water up to 65°C.

Section:

5075 Fibre

Section Subtitle:

These materials are for use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

WRAS Approval Number:

2210517

Expiry date:

31/10/2027

Approval Holder:

Teadit International Produktions GmbH

Company Name

Teadit International Produktions GmbH

Address

Europastrasse 12, 6322 Kirchbichl

Country

Austria

View All Listings by this Company

‘ECOCLEAR White Gray 9098’. Off-white/grey coloured, hot pressed GRP single layered panel. For use with water up to 55°C.

Section:

5120 Glass Reinforced Plastics (GRP)

Section Subtitle:

Components.

WRAS Approval Number:

2302509

Expiry date:

29/02/2028

Approval Holder:

ECOCLEAR Co. Ltd.

Company Name

ECOCLEAR Co. Ltd.

Address

53-1 1288 Beon-gil, Gimhaedae-Ro Hallim-Myeon Gimhae-si, Gyeongsangnam-do, 50581

Country

Korea, Republic of

View All Listings by this Company