SFGV Range of gate valves with ductile iron bodies (blue epoxy coated) and EPDM rubber coated wedges. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C
Range of gate valves with blue coloured epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of angled, screw down stop valves with brass bodies and NBR rubber gasket and ‘O’-rings. Maximum working pressure 10.0 bar. Cold water use only.
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of inlet control groups with DZR brass bodies incorporating an in-line, adjustable, pressure reducing valve (PRV) (adjustable range ±10% of the factory pre-set value - see model), and a pressure relief valve (SRV) (set at 3.0 bar, 4.5 bar or 6.0 bar - see model). The product incorporates a single check valve cartridge, after the pressure reducing valve, verified by test (suitable for backflow protection against Fluid Category 2). The product also incorporates an approved check valve cartridge on the angled cold water take off point, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 10.0 bar. Cold water use only.
Range of in line regulating valves with gunmetal bodies and EPDM ‘O’-rings. The valves incorporate a non-rising spindle headwork for regulating the flow. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of balancing valves with brass or stainless steel bodies and EPDM ‘O’-rings. Maxmimum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of double regulating valves with gunmetal bodies and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of in-line electrolytic or magnetic sale reducers with nickel plated brass bodies. Electrolytic models have a zinc alloy core and magnetic models have a ferrite magnet core. All models are for use with copper pipe manufactured to EN 1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`Scotchkote 206N`. Factory applied, green coloured, epoxy powder coating. Apply and cure as per manufacturer’s 'standard cure guide' which appears in document '80-6111-8352-8 Rev. B'. For use with water up to 23°C.
'SADIP-Mix'. Factory applied, grey coloured cement mortar. Mix sand, cement & water in a mix ratio of 2:1:0.5 and apply as per manufacturer's 'quality work instruction' document 'QW 41A', issue 4 dated 20/11/97. Cure for 24 hours@25°C. The cement mortar must then be submerged in water for 72 hours before use. For use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'JDP21GEY‐5005, JDP21GEY‐5015 & JDP21GEY‐5017'. Factory applied, blue coloured, epoxy powder coatings. Apply as per manufacturer's Technical Data Sheet 'version 1.0', dated 15/02/2022. Cure for 20 minutes@180°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Belzona 1511 (Super HT – Metal)'. Site applied, two-component, silver/grey coloured (once mixed) epoxy coating. Mix parts A and B in a 5:1 mass ratio and apply as per manufacturer's instructions for use 'FN10178', publication number '07-06-21'. Cure for 18 hours@20°C then post-cure for 1 hour@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Regin REGQ102-115'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic Vinyl Ester VE671PA'. Brown coloured (translucent), contact moulded GRP laminating material. For use with water up to 23°C.
Page 98 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
