Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 8.0 bar. Cold water use only.
'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (natural, appear white)'. 'Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials. For use with water up to 85°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.3 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver2 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Corro Coat EP-F1003HW Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's Technical Data Sheet dated '31 July 2018'. Cure for 4 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 924 of 1045
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
