Range of end feed copper solder fittings for use with copper tube. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2112302

Size:

see models

Marking:

Hengshen logo (HS) and size on body.

Installation Requirements:

R001

Expiry date:

31/12/2026

Model:

End feed fittings: 5090 (90°Elbow Close Ruff CxC) 6,8,10,12,15,22,28,35,42,54mm 5092 (90°Street Elbow Close Ruff) 6,8,10,12,15,22,28,35,42,54mm 5090R (Reducing 90° Elbow C×C) 12×10, 12×8, 15×12, 22×15, 28×22, 28×15, 35×28, 35×22, 42×35, 42×28,42x22,54×42, 54×35, 54×28; 5041 (45°Elbow C×C) 6,8,10,12,15,22,28,35,42,54mm 5040 (45°Elbow FTG×C) 6,8,10,12,15,22,28,35,42,54mm 5002A (90°Elbow Long TurnC×C) 6,8,10,12,15,22,28,35,42,54mm 5001A (90°Street Elbow Long Turn Ftg×C) 6,8,10,12,15,22,28,35,42,54mm 5130 (Equal Tee C×C×C) 6,8,10,12,15,22,28,35,42,54mm 5130R (Reducing TEE C×C×C) 6x6x8, 8×8×6, 10×10×15, 12×12×10, 12×12×8, 12×10×10, 12×8×8, 15×15×22, 15×15×12, 15×15×10, 15x15x8, 15×12×15, 15×12×12, 15×12×10, 15×12×8, 15x10x15, 15x10x10, 22×22×28, 22×22×15, 22×22×12, 22×15×22, 22×15×15, 22×15×12, 28×28×22, 28×28×15, 28×22×28, 28×22×22, 28×22×15, 28x15x28, 28x15x22, 28×15×15, 35×35×28, 35×35×22, 35×35×15, 35×28×35, 35×28×28, 35×28×22, 35×22×35, 35×22×28, 35×22×22, 35×15×35, 42×42×35, 42×42×28, 42×42×22, 42x42x15, 42×35×42, 42×28×42, 42×22×42, 54×54×42, 54×54×35, 54×54×28, 54×54×22, 54×54×15,54×42×54, 54×35×54 5270 (Equal Coupling C×C) 6,8,10,12,15,22,28,35,42,54mm 5240 (Reducing Coupling C×C) 8×6, 10×8, 10×6, 12×10, 12×8, 12×6, 15×12, 15×10, 15×8, 22×15, 22×12, 22×10, 28×22, 28×15, 28×12, 35×28, 35×22, 35×15, 42×35, 42×28, 42×22, 42×15, 54×42, 54×35, 54×28, 54×22, 54×15 5243 (Fitting Reducer Ftg×C) 8×6, 10×8, 10×6, 12×10, 12×8, 12×6, 15×12, 15×10, 15×8, 22×15, 22×12, 22×10, 28×22, 28×15, 28×12, 35×28, 35×22, 35×15, 42×35, 42×28, 42×22, 42×15, 54×42, 54×35, 54×28, 54×22, 54×15 5301 (Tube Cap) 6,8,10,12,15,22,28,35,42,54mm 5060 (Return Bend C×C) 6,8,10,12,15,22,28,35,42,54mm 5085 (Cross Over Coupling C×C) 15, 22mm 5086 (Partial Cross Over Ftg×C) 15, 22mm 5062 (Straight Tap Connector C×FI) 15×1/2”, 15×3/4”, 22×3/4”, 22×1",28×1" 5063 (Bent Tap Connector C×FI) 15×1/2”, 15×3/4”, 22×3/4”, 22×1",28×1" Solder ring fittings: SR5090 (90°Elbow Close Ruff C×C) 8,10,12,15,22,28,35,42,54mm SR5092 (90°Street Elbow Close Ruff Ftg×C) 15,22,28mm SR5090R (Reducing 90° Elbow C×C) 22×15, 28×22, 28×15 SR5041 (45°Elbow C×C) 8,10,12,15,22,28,35,42,54mm SR5040 (45°Elbow FTG×C) 15,22,28mm SR5130 (Equal Tee C×C×C) 8,10,12,15,22,28,35,42,54mm SR5130R (Reducing TEE C×C×C) 15×15×10, 15×15×12, 15×15×22, 22×22×28, 22×22×15, 22×22×12, 22×15×22, 22×15×15, 28×28×22, 28×28×15, 28×22×28, 28×22×22, 28×22×15, 28×15×28, 28×15×22,28×15×15, 35×35×28, 35×35×22, 35×35×15, 42×42×35, 42×42×28, 42×42×22, 42×42×15, 54×54×42,54×54×35, 54×54×28, 54×54×22, 54×54×15 SR5270 (Equal Coupling C×C) 8,10,12,15,22,28,35,42,54mm SR5240 (Reducing Coupling C×C) 10×8, 12×10, 12×8, 15×12, 15×10, 15×8, 22×15, 22×12, 22×10, 28×22, 28×15, 28×12, 35×28, 35×22, 35×15, 42×35, 42×28, 42×22, 42×15, 54×42, 54×35, 54×28, 54×22, 54×15 SR5243 (Fitting Reducer Ftg×C) 10×8, 12×10, 12×8, 15×12, 15×10, 15×8, 22×15, 22×12, 22×10, 28×22, 28×15, 28×12, 35×28, 35×22, 35×15, 42×35, 42×28, 42×22, 42×15, 54×42, 54×35, 54×28, 54×22, 54×15 SR5301 (Tube Cap) 8,10,12,15,22,28,35,42,54mm SR5085 (Cross Over Coupling C×C) 15,22mm SR5086 (Partial Cross Over Ftg×C) 15,22mm SR5062 (Straight Tap Connector C×FI) 15×1/2”, 15×3/4”, 22×3/4” SR5063 (Bent Tap Connector C×FI) 15×1/2”, 15×3/4”, 22×3/4

Approval Holder:

Ningbo Hengsheng Pipe Fitting Co Ltd

Company Name

Ningbo Hengsheng Pipe Fitting Co Ltd

Address

No. 28 West Jinshui Road, Ninghai, Zhejiang

Country

China

Phone

0086-574-65338995

General Email

sales@hengshen.com

View All Listings by this Company

‘Endex’ range of copper alloy and copper end feed fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2202701

Marking:

Endex (brand of Pegler Yorkshire Ltd.) and size on body

Installation Requirements:

R001

Expiry date:

28/02/2027

Model:

Endex range consisting of: N1 STRAIGHT COUPLING: 6mm to 54mm N1IM ADAPTOR COUPLING: 15mm x ½” to 28mm x 1” N1R REDUCING COUPLING: 8mm x 6mm to 54mm x 42mm N1SLIP STRAIGHT COUPLING SLIP: 15mm to 54mm N2 STRAIGHT FEMALE CONNECTOR: 15mm x 3/8" to 54mm x 2” N3 STRAIGHT MALE CONNECTOR: 15mm x 3/8" to 54mm x 2” N6 REDUCER: 8mm x 6mm to 54mm x 42mm N7 FEMALE ADAPTOR: 15mm x ½” to 54mm x 2” N8 MALE ADAPTOR: 15mm x ½” to 54mm x 2” N9 ADAPTOR: ½” x 15mm to ¾” x 22mm N11 UNION COUPLING CONE FACE: 15mm to 54mm N12 ELBOW: 8mm to 54mm N12R REDUCING ELBOW: 22mm x 15mm N12S STREET ELBOW: 10mm to 54mm N13 MALE ELBOW: 15mm x 1/2” to 28mm x 1” N14 FEMALE ELBOW: 15mm x ½” to 35mm x 1.1/4” N15 BACKPLATE ELBOW: 15mm x ½” to 22mm x ¾” N18 SLOW BEND: 10mm to 54mm N18S SLOW STREET BEND: 10mm to 54mm N21 OBTUSE ELBOW 45°: 12mm to 54mm N21S OBTUSE STREET ELBOW 45°: 15mm to 54mm N22 PARTIAL CROSSOVER: 15mm to 22mm N23 FULL CROSSOVER: 15mm to 22mm N24 EQUAL TEE: 6mm to 54mm N25 TEE REDUCED BRANCH: 15mm x 15mm x 10mm to 54mm x 54mm x 42mm N26 TEE ONE END REDUCED: 18mm x 15mm x 18mm to 54mm x 42mm x 54mm N27 TEE ONE END AND BRANCH REDUCED: 15mm x 12mm x 12mm to 54mm x 42mm x 42mm N28 TEE BOTH ENDS REDUCED: 10mm x 10mm x 12mm to 35mm x 35mm x 42mm N29 FEMALE TEE: 15mm x ½” x 15mm N29R FEMALE TEE: 22mm x ½” x 22mm to 28mm x ½” x 28mm N30 FEMALE TEE: 15mm x 15mm x ½” to 28mm x 28mm x 1” N30R FEMALE TEE: 22mm x 22mm x ½” to 35mm x 35mm x ½” N50 CROSS: 15mm to 22mm N61: 8mm to 54mm N61AV STOP END: 15mm N62 STRAIGHT TAP CONNECTOR: 15mm x ½” to 22mm x ¾” N63 BENT TAP CONNECTOR: 15mm x ½” to 22mm x ¾” N64 BENT UNION ADAPTOR: 15mm x ¾” N65 BENT MALE UNION CONNECTOR: 15mm x ½” to 28mm x 1” N68 STRAIGHT UNION ADAPTOR: 15mm x ¾” to 28mm x 1¼” N68FF FLAT FACED UNION ADAPTOR: 22mm x ¾” N68 METER UNION: 22mm x ¾” N69 STRAIGHT MALE UNION CONNECTOR: 15mm x ½” to 54mm x 2”

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Dudley S9 dual flush syphonic flushing apparatus with a polypropylene body and stainless steel link for use with WC flushing cisterns.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not be verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2202900

Size:

1½” Outlet, Syphon heights 7½” to 12”.

Marking:

DUDLEY HI-FLO S9B SYPHON on top of valve body.

Installation Requirements:

R001

Expiry date:

31/12/2026

Model:

S9 Syphon

Approval Holder:

Thomas Dudley Limited

Company Name

Thomas Dudley Limited

Postcode

DY1 4SJ

Country

United Kingdom

Phone

0121 530 7053

General Email

jcresswell@thomasdudley.co.uk

View All Listings by this Company

Manufacturer:

Thomas Dudley Limited

Company Name

Thomas Dudley Limited

Postcode

DY1 4SJ

Country

United Kingdom

Phone

0121 530 7053

General Email

jcresswell@thomasdudley.co.uk

View All Listings by this Company

OMEG range of wall mounted, near-boiling water dispensers (cased and insulated). The products incorporate a solenoid valve which controls the flow, a stainless-steel tank, 3 or 5L (see model), and a plastic strainer at the inlet. Maximum supply pressure 10.0 bar. Cold water supply only. Maximum operating temperature 95˚C

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

2111024

Size:

¾” BSP (M) inlet.

Marking:

HYCO on front of unit. HYCO & OMEG on technical label.

Installation Requirements:

R001 R040

Expiry date:

30/11/2026

Model:

OMEG3 and OMEG5

Product Images

Approval Holder:

Hyco Manufacturing Ltd

Company Name

Hyco Manufacturing Ltd

Address

California Drive, Castleford, West Yorkshire

Postcode

WF10 5QH

View All Listings by this Company

Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressure relief valve set at 3.0 bar. The supplies to both primary hot water and secondary are controlled via spherical valves. The boilers incorporate a filling loop assembly which incorporates a double check valve assembly (suitable for backflow protection against Fluid Category 3). Primary circuit: Maximum working pressure 2.5 bar. Maximum operating temperature 82°C. Secondary circuit: Maximum working pressure 10.0 bar. Maximum operating temperature 60°C

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

2110320

Size:

22mm compression

Marking:

Worcester (brand of Bosch) on front of boiler. Worcester, address, model, serial No. & other tech info on adhesive label on inside of panel.

Installation Requirements:

R001

Expiry date:

31/10/2026

Model:

Greenstar Highflow range comprising of model numbers: 7 731 600 098 (model code: 440CDi ErP). 7 731 600 099 (440CDi ErP). 7 731 600 100 (550CDi ErP). 7 731 600 101 (550CDi ERP).

Product Images

Approval Holder:

Worcester Bosch

Company Name

Worcester Bosch

Address

Cotswold Way Warndon Worcester

Postcode

WR4 9SW

Country

United Kingdom

Phone

+44 1905 752761

General Email

ian.sharp@uk.bosch.com

View All Listings by this Company

Manufacturer:

Worcester Bosch

Company Name

Worcester Bosch

Address

Cotswold Way Warndon Worcester

Postcode

WR4 9SW

Country

United Kingdom

Phone

+44 1905 752761

General Email

ian.sharp@uk.bosch.com

View All Listings by this Company

Range of air cooled ice making machines . Inlet is controlled via solenoid valve. Maximum working pressure 5.5 bar. Cold water use only.

Section:

1500 Ice Making Machines

Size:

See model.

Marking:

Manitowoc logo on door. Manitowoc, model, serial number & technical information on body.

Installation Requirements:

R001 R009 R160 R171 R511

Expiry date:

31/10/2026

Model:

I(*)T0300A I(*)T0300W I(*)P0320A I(*)T0420A I(*)T0450A I(*)T0450W I(*)T0500A I(*)P0500A I(*)T0620A I(*)T0620W I(*)T0750A I(*)T0750W I(*)T0900A I(*)T0900W I(*)T1200A I(*)T1200W I(*)T1200N IBT1020C I(*)T1500A I(*)T1500W I(*)T1500N I(*)T1900A I(*)T1900N I indicates Indigo family of Ice Machines (*) Indicates D, Y or R. Dependent on ice cube size (T or P) Indicates refrigerant type (T=R410A, P=R290) 4 numerical characters indicate to icemaking capacity per 24hrs Final character indicates cooling option (A=Air, W=Water, N=Remote Condenser, C=Remote Condensing Unit)

Models added July 2024: I(*)P0300A I(*)P0420A I(*)P0620A I(*)P0620W I(*)P0600A I(*)P0600W I(*)P0900A I(*)P0900W I(*)P1200A I(*)P1200W I(*)P1200N I(*)P1500A I(*)P1500W I(*)P1500N I(*)P1900A I(*)P1900N

Product Images

Approval Holder:

Pentair Commercial Ice LLC

Company Name

Pentair Commercial Ice LLC

Address

5500 Wayzata Blvd. Suite 900 Golden Valley, MN

Postcode

55416

Country

United States

General Email

jeng.yang@pentair.com

View All Listings by this Company

Manufacturer:

Pentair Commercial Ice LLC

Company Name

Pentair Commercial Ice LLC

Address

5500 Wayzata Blvd. Suite 900 Golden Valley, MN

Postcode

55416

Country

United States

General Email

jeng.yang@pentair.com

View All Listings by this Company

Range of ultrasonic water meters with brass bodies incorporating EPDM ‘O’-rings. The inlets incorporate a plastic strainer. The DN15 X 165mm and DN20 X 190mm models incorporate a non-return valve on the outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.

Section:

1505 Water Meters

Size:

DN15 models: ¾” BSP (M). DN20 model: 1” BSP (M).

Marking:

Badger Meter, size, flow arrow, model name, date of manufacture (MM/YY) and technical information on meter face. Flow arrow and size on body.

Installation Requirements:

R001

Expiry date:

31/12/2026

Model:

E-Series G2® Ultrasonic Meter Range: DN15 X 110 ultrasonic meter, meter body: Eco Brass C69300, DN15 X 114 ultrasonic meter, meter body: Eco Brass C69300, DN15 X 165 ultrasonic meter, meter body: Eco Brass C69300, DN20 X 190 ultrasonic meter, meter body: Eco Brass C69300.

Product Images

Approval Holder:

Badger Meter Inc.

Company Name

Badger Meter Inc.

Address

4545 W Brown Deer Road, Milwaukee WI

Postcode

53223

Country

United States

Phone

+1 414 371 5941

General Email

rschultz@badgermeter.com

View All Listings by this Company

Manufacturer:

Badger Meter Inc.

Company Name

Badger Meter Inc.

Address

4545 W Brown Deer Road, Milwaukee WI

Postcode

53223

Country

United States

Phone

+1 414 371 5941

General Email

rschultz@badgermeter.com

View All Listings by this Company

Range of single-jet water meters with brass bodies and a plastic strainer on the inlet. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.

Section:

1505 Water Meters

Size:

see model

Marking:

GWF barcode, max pressure, flow rate, model, year of production (YYYY), GWF and other techical info on meter face.

Installation Requirements:

R001 R120

Expiry date:

31/12/2026

Model:

Unico2 and Unico2coder MP: Qn 1.5 (Q3 2.5) G3/4B DN15 110mm: ¾” BSP (M), Qn 1.5 (Q3 2.5) G1B DN20 110mm: 1” BSP (M), Qn 1.5 (Q3 2.5) G1B DN20 130mm: 1” BSP (M), Qn 2.5 (Q3 4.0) G1B DN20 130mm: 1” BSP (M). Models added April 2025: Unico2e: Qn 1.5 (Q3 2.5) G3/4B DN15 110mm: ¾” BSP (M), Qn 1.5 (Q3 2.5) G1B DN20 110mm: 1” BSP (M), Qn 1.5 (Q3 2.5) G1B DN20 130mm: 1” BSP (M), Qn 2.5 (Q3 4.0) G1B DN20 130mm: 1” BSP (M).

Product Images

Approval Holder:

GWF AG

Company Name

GWF AG

Address

Obergrundstrasse 119 Lucerne

Postcode

6005

Country

Switzerland

Phone

+41 41 319 51 77

General Email

moritz.roettger@gwf.ch

View All Listings by this Company

Manufacturer:

GWF AG

Company Name

GWF AG

Address

Obergrundstrasse 119 Lucerne

Postcode

6005

Country

Switzerland

Phone

+41 41 319 51 77

General Email

moritz.roettger@gwf.ch

View All Listings by this Company

Range of in line regulating valves DZR brass bodies, EPDM ‘O’-rings and PTFE seals. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1530 Miscellaneous Fittings

Size:

½” – 2” BSP F.

Marking:

Pegler on operating member. Pegler logo, CR, PN, size and flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/12/2026

Model:

½” 1260MF – item code 126043. ½” 1260LF – item code 126022 ½” 1260ULF – item code 126039 ½” 1260SF – item code 126023 ¾” 1260SF – item code 126024 1” 1260SF – item code 126025 1¼” 1260SF – item code 126026 1½” 1260SF – item code 126027 2” 1260SF – item code 126028 MF = Medium Flow LF = Low Flow ULF = Ultra Low Flow SF = Standard Flow

Product Images

Approval Holder:

Pegler Yorkshire Ltd

Company Name

Pegler Yorkshire Ltd

Address

St Catherines Avenue, Balby Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

+44 (0) 844 243 4400

View All Listings by this Company

Water hammer arrestor with brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.

Section:

1530 Miscellaneous Fittings

Marking:

RBM on body

Installation Requirements:

R001

Expiry date:

31/03/2026

Model:

30720400

Approval Holder:

RBM S.p.a.

Company Name

RBM S.p.a.

Address

Componenti Per Impianti Idrotermici Via S. Giuseppe, 1 25075 Nave (Brescia)

Country

Italy

View All Listings by this Company