'CPT CML Variation No.2 cementitious mortar’ for use with ‘Conplast RP264 Admixture'. Site applied, grey coloured (once mixed) cementitious mortar and admixture. 'CPT CML Variation No.2 cementitious mortar’ comprises of cement, sand and Microsilica. Mix cement and sand dry in a 1:1.1 mass ratio. Add the microsilica in a 1:0.05 mass ratio with the cement content. Add water in a cement/water mass ratio of 1:0.32. Add the admixture in an admixture/ cement ratio of 8ml:1000g. Mix rigorously until an even consistency is achieved and apply as per manufacturer’s instructions reference ‘2328’, dated 13/01/2023. Cure for 28 days@ between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tiefill'. Site applied, grey coloured cementitious repair mortar. Mix Tiefill with water in a weight ratio of 9.4:1 and apply in accordance with manufacturer’s instructions for use 'bulletin no. TFILL/031/003, issued 'July 2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Atlac 430'. Yellow coloured, vinyl ester resin material manufactured by filament winding. For use with water up to 60°C.
'Borsafe ME3440 (black), Borsafe ME3444 (blue) & Borsafe ME3440-W (black)'. PE80 materials suitable for injection moulding and extrusion purposes. For use with water up to 60°C.
'PPE HY3140G'. Black coloured, injection moulded PPE material. For use with water up to 85°C.
'RP2400'. White coloured, extruded polypropylene pipe. For use with water up to 85°C.
'BOSS 79024607'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'Inoflon® GN7040 & Inoflon® MGN7045'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
‘TWK7534, TWK5810, TWK5811, TWK5812, TWK5813, TWK5814, TWK5815’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'4711'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'Spray SLC STD Inlay 24' & 'Spray SLC STD Inlay 16 Low'. Grey coloured, injection moulded, liquid silicone rubber components. Shore hardness 70. Tested in-radius size 0.44mm. For use with water up to 70°C.
SIL4010, SIL5010 & SIL6010 white translucent. SIL4010, SIL5010, SIL6010 & SIL7010 blue. SIL4010, SIL5010, SIL6010 & SIL7010 red. SIL4010, SIL5010, SIL6010 & SIL7010 yellow. Compression moulded silicone rubber materials. Shore hardness between 40 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Berner Green Paste'. Green coloured, polymer sealing paste. Apply as per manufacturer's Technical Data Sheet '46845(P)', dated 'December 2019'. For use with water up to 85°C.
'Weld-On 725 Wet 'R' Dry Clear Solvent Cement'. Clear, colourless solvent cement. ‘Weld-On 725 Wet ‘R DRY Blue PVC Cement’ was added to the approval in September 2025. Blue coloured solvent cement. Cure for between 1 & 4 hours@5°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Weld-On 724 C-PVC Grey Solvent Cement' Grey coloured solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 719 PVCu Clear Solvent Cement'. Clear, colourless solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C(±2°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maritex Aquapure Grade 5742'. Beige coloured tube manufactured by winding PET fibre and epoxy vinylester resin over a mandrel under heat and pressure, intended for the manufacture of bearings. For use with water up to 23°C.
Range of deck mounted taps for cold or premixed water with stainless steel bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor, and the spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and the temperature is controlled via a ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a single check valve assembly (verified by test suitable for backflow protection against Fluid Category 2) and the inlet incorporates a stainless-steel strainer. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted tap assemblies for cold or premixed water with chromium plated brass bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor and the spout outlets have plastic aerators. Supplied with stainless steel braided PEX lined connection hoses. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 91 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
