'Rapal Light C795' disc. White coloured, compression moulded, ring shaped ceramic gliding disc. For use with water up to 85°C.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. Resicoat R4 blue R4-FB HJC06R & R4-ES HJF26R. Resicoat R4 red/red-brown R4-ES HGF03R. Resicoat R4 black R4-FB HNC01R. Resicoat R4 black: R4-ES HNF04R.
'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add PLUS 2.5'. Grey coloured, site-applied waterproofing admixture. Admixture is to be added to cement mix in a dosing ratio of 2.5 kg per m3 of concrete. Cure for 5°C for 48 hours. For use with water up to 23°C. This material is only approved for the dosing and curing conditions that appear on the approval. If the dosing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LATTYflon 4789'. Yellow coloured, braided fibre/PTFE gland packing. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'LATTYgraf EFA'. Grey coloured, graphite sheet material manufactured by calendaring. For use with water up to 85°C.
'SANIBIW WB-R Reinforced Multilayer Hoses' and ‘SANIBIW WB-R Hose’. 'SANIBIW WB-R Reinforced Multilayer Hoses' are dual layered, extruded hoses, consisting of an off-white translucent (natural) silicone rubber inner layer and VMQ silicone rubber (with PES reinforcement) outer layer. The outer layer is available in black, red/brown, white or silver colours. Shore hardness 70. The inner and outer layers each have a tested in-radius size of 1.1mm. ‘SANIBIW WB-R Hose’ is a single layered, translucent (natural), extruded silicone rubber hose with PES reinforcement. Shore hardness 70. Tested in-radius size of 2.0mm. All hoses are for use with water up to 85°C.
'SANIBIW WB Hose’. Single layered, uncoloured & translucent (natural), extruded silicone rubber hose. Shore hardness 70. Tested in-radius size of 2.0mm. For use with water up to 85°C.
'Seplite LSF 983'. White coloured ion exchange resin. For use with water up to 85°C.
'IKV Tribosil MHL 40'. Clear silicone liquid lubricant. Apply as per manufacturer's technical data sheet. No cure required. For use with water up to 85°C.
'RADILON® A RV300RKC 306 BK' (black coloured). In December 2022, 'RADILON A RV300RKC 106 NT' (natural, appears off-white) was added to the approval. Injection moulded PA66-GF30 materials. For use with water up to 85°C.
‘Ultramid® A3EG10 FC Aqua Black 23285’. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'Akoalit PB 4268 White & Akoalit PB 4267 Grey'. White or grey coloured, extruded polybutylene material. For use with water up to 85°C.
'Akoalit PB R 539'. Natural (which appears white coloured), compression moulded polybutylene material. For use with water up to 85°C.
'PB DKG 300'. Natural, (appears beige coloured), compression moulded polybutylene material. For use with water up to 85°C.
`Pocan B1501 000000`. Natural (appears white coloured), injection moulded PBT material. For use with water up to 85°C.
Page 89 of 394
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
