‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SADIP-Mix'. Factory applied, grey coloured cement mortar. Mix sand, cement & water in a mix ratio of 2:1:0.5 and apply as per manufacturer's 'quality work instruction' document 'QW 41A', issue 4 dated 20/11/97. Cure for 24 hours@25°C. The cement mortar must then be submerged in water for 72 hours before use. For use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal'. Factory applied, red-brown coloured (once mixed and applied), two-part polyurethane coating. Mix, apply and cure (full cure of 7 days@30°C) as per manufacturer's instructions ref. 'DI/PU/2022/072', dated 25/04/2022. For use with water up to 35°C.
'Purtop Easy DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS '7483-7-2021-I-gb'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KLINGERSIL® C-4324'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Crystic 274E`. Olive coloured, contact moulded, GRP unsaturated polyester material. For use with water up to 23°C.
'Polylite 444-M888'. Amber coloured, unsaturated polyester resin material manufactured by liquid casting. For use with water up to 23°C.
'Poseidon Cable' (3 x 1.5mm, 4 x 1.5mm, 3 x 1.0mm & 4 x 1mm). Blue coloured (external water contact layer), extruded, XLPE electrical cable. For use with water up to 65°C.
'Pexylene 45939 Black'. Black coloured polyethylene material manufactured by rotomoulding. For use with water up to 85°C.
'LL 8460.29'. Natural (appears white and opaque) LLDPE material manufactured by rotational moulding. For use with water up to 85°C.
‘FORTRON 9115L0 SD3039 BLACK (formerly known as FORTRON MT9115L0 SD3039 DW black) & FORTRON 9141L4 SD3039 BLACK (formerly known as FORTRON MT9141L4 SD3039 DW black’). Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'BC 245 MO Polypropylene Cover'. White coloured, injection moulded, circular polypropylene cover component. For use with water up to 85°C.
‘FILTER NOZZLES P, PTL, P5, P6, P7, T, TTL, TD, R, RTL, RD, B, V, VL, C, D4, D3 & D9. NUTS N & HR. EXPANDING BOLT TS. VALVE BODIES DPI & DPS. SLEEVES G, GM & GE. COLLECTORS CSI05, CSI06, CST06, CSD06, CSI08, CST08, CSG08, CSD08 & CSI08. FILTER ARMS SF/SFC, SD, SB & SC. FILTER NOZZLES RB2 & RB3. DISTRIBUTORS RBD2 & RBD3’. Blue, black, dark grey, light grey, green, red, yellow & light blue coloured, injection moulded polypropylene components. For use with water up to 23°C.
‘Verplen C30 01 NE ACLKUV (black coloured), C30 04 NE ACLUV (black coloured), C30 08 NE ACLKUV (black coloured) & C30 08 NT ACLKUV (natural – appears beige coloured)’. Injection moulded, glass filled polypropylene materials. For use with water up to 60°C.
'INOLUB™ T201F, T202F, T203F, T204F & T205F'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'V7500BK'. Black coloured, Fluororubber material manufactured by mould pressing. Shore hardness 75. Tested in-radius size 1.04mm. For use with water up to 23°C.
Page 86 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
