'TEC N41-70 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
'SIL8701 Red 'O'-rings'. Red coloured, injection moulded silicone rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
'LP60ANAT 368'. Natural (appears off-white), compression moulded silicone rubber material. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LP4411ANAT, LP37ANAT, LP4611ANAT & LP4811ANAT'. Natural (off-white coloured), compression moulded silicone rubber materials. Shore hardness 40°, 60° and 80° respectively. Tested in-radii sizes between 1.0mm and 2.0mm. For use with water up to 85°C.
'LSR2650, LSR2660 & LSR2670'. Black coloured, injection moulded liquid silicone rubber materials. Shore hardness between 50 & 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Sikasil DW Trans'. Site applied silicone sealants available in transparent (CO0 transparent), grey (RA1 7004) or black (CO4 Schwarz). Apply as per manufacturer's instructions Product Data Sheet 'April 2022, Version 04.01'. Cure for 24 hours@7°C. The transparent (CO0 transparent) and grey (RA1 7004) sealants are for use with water up to 85°C. The black (CO4 Schwarz) sealant is for use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'FIX 247 (product code 070323)'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Hinton Equipment (product code JJC250)'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Loctite® AA 326 with Loctite® SF 7649™ Activator'. Loctite® AA 326 is an amber coloured, liquid anaerobic adhesive and Loctite® SF 7649™ is a green coloured, liquid activator. Apply as per manufacturer's Technical Data Sheet dated December 2013. Cure 7 days@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RIAMAXX HR XE4350 KTW grau R-7040'. Grey coloured, injection moulded, glass filled aliphatic polyketone material. For use with water up to 60°C.
Range of wall mounted electric showers (various finishes). The GSD/BETTER models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/DSK/ENTRY models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). Incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). The GSD models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/ models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single hole, single outlet, fixed, electronically controlled tap assemblies with brass bodies (various finishes), incorporating an electronic cartridge controlling the flow which is activated via an infrared sensor (either battery or mains powered). Models 31 171 xxx & 31 173 xxx incorporates a manually operated temperature control. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet incorporates a flow regulator and the spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated via an infra-red sensor either battery or power supply. The product incorporates a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bottom or side entry BS1212-4 (2016) compact type float operated inlet valves for WC flushing cisterns incorporating plastic flow regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Page 86 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
