'Nu Vista'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours at 45°C and then 28 days (672 hours)@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Infra Pro'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours@45°C and then 28 days (672 hours) @35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
"Bond-It Tanking Slurry". Site applied, grey coloured, two part (powder & water) cementitious waterproof coating. Mix and apply as per manufacturer`s instructions 'Version 9' dated 06/08/20. Cure for 12 days at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EZY-PAK™ #100 Packing Compound'. White coloured, PTFE packing compound. Apply as per 'Jet-Lube' TDS for 'EZY-PAK™ #100'. For use with water up to 23°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'DAEWOO GRP Panel'. Beige coloured, hot press moulded GRP panel. For use with water up to 50°C.
`DR-PNL-WT Tank Panel`. Grey coloured GRP panel manufactured by hydraulic press moulding. For use with water up to 50°C.
`Polyver-3345`. Orange/brown coloured, contact moulded vinyl ester resin material. For use with water up to 50°C.
`Polyver-3045`. Brown coloured, contact moulded vinyl ester resin material. For use with water up to 50°C.
'C107DQ (Na), C108DQ (Na) & C110DQ (Na)'. Light yellow coloured ion exchange resins. For use with water up to 23°C.
'IKV Tribostar STF 2501 & Addisil WTG 1'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'TYPLEX-1055'. Grey coloured, extruded Polybutylene-1 material. For use with water up to 85°C.
'Ultradur® B4300 G6 HR FC Aqua grey 35413 '. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
`Polygel-2132`. Yellow coloured, contact moulded Gelcoat. For use with water up to 50°C.
'POLYISO 200 NA'. Amber coloured (transparent), contact moulded polyester material. For use with water up to 50°C.
'Helisystem CT fitting'. Green coloured, injection moulded PP-RCT fitting. Between July 2021 and September 2022, the fitting was for use with water up to 23°C. Between October 2022 and July 2026, the fitting is for use with water up to 75°C.
`PPR 001` Pipes. White (with red external stripe) or tangerine coloured, extruded polypropylene pipes. For use with water up to 85°C.
'100-HR25'. White coloured (translucent), injection moulded polypropylene material. For use with water up to 23°C.
'Ultrason® S2010 Natural'. Natural (colourless), injection moulded polysulphone material. For use with water up to 85°C.
Page 85 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
