Directory Search Results

Print List

#250555026

‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:
5030 Coatings, Paints & Linings
Section Subtitle:
Factory applied pipe & fittings coatings.
WRAS Approval Number:
250555026
Expiry date:
31/05/2030

Approval Holder:
Tata Steel Limited
Company Name
Tata Steel Limited
Address
Metaliks Division, Vill - Maheshpur, PO Samraipur, PS - Kharagpur Local, Dist.Paschim Medinipur, West Bengal, Pin - 721301
Country
India

View All Listings by this Company

Print This Approval


#250455038

'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:
5042 Coatings, Paints & Linings
Section Subtitle:
Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.
WRAS Approval Number:
250455038
Expiry date:
30/04/2030

Approval Holder:
Saudi Vetonit Co. Ltd. (SAVETO)
Company Name
Saudi Vetonit Co. Ltd. (SAVETO)
Address
PO Box 52235, Riyadh 11563
Country
Saudi Arabia

View All Listings by this Company

Print This Approval


#250455039

'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:
5042 Coatings, Paints & Linings
Section Subtitle:
Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.
WRAS Approval Number:
250455039
Expiry date:
30/04/2030

Approval Holder:
Saudi Vetonit Co. Ltd. (SAVETO)
Company Name
Saudi Vetonit Co. Ltd. (SAVETO)
Address
PO Box 52235, Riyadh 11563
Country
Saudi Arabia

View All Listings by this Company

Print This Approval


#250455049

'Grivory HT1VA-4 FWA (Natural) & Grivory HT1VA-4 FWA black 9225'. Natural (appears beige-green coloured) & black, injection moulded nylon materials. For use with water up to 85°C.

Section:
5180 Nylon
Section Subtitle:
Material only. Components made from materials listed in this section may be required to be submitted for audit tests.
WRAS Approval Number:
250455049
Expiry date:
30/04/2030

Approval Holder:
EMS-CHEMIE AG
Company Name
EMS-CHEMIE AG
Address
Via Innovativa 1, CH-7013 Domat/Ems
Country
Switzerland
Phone
+41 81 632 78 78
General Email
welcome@emsgrivory.com

View All Listings by this Company

Print This Approval


#250555019

'Badadur PBT9 GF10 WL Blau 1001'. Blue coloured, injection moulded PBT material. For use with water up to 23°C.

Section:
5205 Polybutylene Terephthalate
Expiry date:
31/05/2030

Approval Holder:
Bada AG
Company Name
Bada AG
Address
Untere Strut 1, D-77815 Bühl/Baden
Country
Germany
General Email
waldecker@bada.de

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 781 of 820

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.