Range of screw-down stop valves with brass bodies, incorporating a non-rising spindle operated via a T shaped (all models excluding 513042) or hand wheel operating member (model 513042 only) and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of screw down stop valves with brass bodies and EPDM gaskets. M profile press connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down angle valves (chromium plated brass) incorporating a dome or triangular type operating member with a NBR washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 8.6 bar. Cold water use only.
Range of undercounter water chillers with a stainless-steel cooling tank including a drain outlet. Maximum working pressure 3.0 Bar. Maximum operating temperature 38°C.
'PA-727 CM1404 White & PA-727 CM1405 Grey'. White or grey coloured, injection moulded ABS materials. PA-727 CM1404 White is for use with water up to 85°C. PA-727 CM1405 Grey is for use with water up to 23°C.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 706 of 1132
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
